Allen-Bradley 1756-M02AE User Manual Download Page 79 | Manualshive

Page: 79 / 236

Allen-Bradley 1756-M02AE User Manual Download Page 79

Geometries with no orientation support

Chapter 3

Rockwell Automation Publication MOTION-UM002F-EN-P - February 2018

79

If the range-of-motion values for the articulated
robot are:

Typically, the work envelope is:

J1 = ± 170
J2 = 0 to 180
J3 = ± 60
L1 = 10
L2 = 12

Top view - Depicts the envelope of the tool center point sweep in J1 and J3 while J2 remains at a fixed position of
0 .

Side view - Depicts the envelope of the tool center point sweep in J2 and J3 while J1 remains at a fixed position of
0 .

See also

Configuration parameters for Articulated Dependent robot

Articulated dependent robot

Configure the Logix Designer application to control robots with varying reach
and payload capacities. Be sure to have these configuration parameter values for

the robot:

•

Link lengths

•

Base offsets

•

End-effector offsets

The configuration parameter information is available from the robot

manufacturer.

Configuration parameters for
Articulated Dependent robot

«
...
77
78
79
80
81
...
»

Summary of Contents for 1756-M02AE













































































































































































































































Reviews:

No comments