Allen-Bradley 1756-M02AE User Manual Download Page 166

Page: 166 / 236

Chapter 4

Geometries with orientation support

166

Rockwell Automation Publication MOTION-UM002F-EN-P - February 2018

The configuration parameter information is available from the robot

manufacturer.

Important:

Verify that the values for the

Link Lengths

Base Offsets

, and

End-Effector Offsets

are entered in the

Coordinate System Properties

dialog box using the same measurement units.

See also

Link Lengths for Delta J1J2J3J6 robot

page 166

Base and Effector Plate dimensions for Delta J1J2J3J6 robot

page 167

Swing Arm offsets for Delta J1J2J3J6 robot

page 168

Configure Zero Angle Orientation for Delta J1J2J3J6 robot

page 170

Link lengths are the rigid mechanical bodies attached at the rotational joints. The

four-dimensional Delta robot geometry has three link pairs made up of

and

. Each link pair has the same dimensions.

•

- link attached to each actuated joint (J1, J2, and J3)

•

- link attached to L1 on one end and the end plate at the other end

Enter the link lengths on the

Geometry

tab in the

Coordinate System

Properties

dialog box.

Link Lengths for Delta J1J2J3J6
robot

Summary of Contents for 1756-M02AE













































































































































































































































Search results

Summary of Contents for 1756-M02AE

Reviews:

Allen-Bradley 1756-M02AE, User Manual, Page: 166 / 236

Search results

Summary of Contents for 1756-M02AE

Reviews: