manualshive.com logo in svg

Allen-Bradley 1734-OE4C, Installation Instructions Manual, Page: 9 / 22

Share
Download
Allen-Bradley 1734-OE4C Installation Instructions Manual Download Page 9

POINT I/O 4 Channel Analog Current Output Module     

9

Publication 1734-IN034C-EN-E - August 2016

Install the Module

The module can be installed before or after base installation. Make sure that the mounting 
base is correctly keyed before installing the module into the mounting base. In addition, 
make sure the mounting base locking screw is positioned horizontal referenced to the base.

1734-TB Base

WARNING: 

When you insert or remove the module while backplane power 

is on, an electrical arc can occur. This could cause an explosion in hazardous 
location installations.

 Be sure that power is removed or the area is nonhazardous before 
proceeding. Repeated electrical arcing causes excessive wear to contacts on 
both the module and its mating connector. Worn contacts may create 
electrical resistance that can affect module operation.

Turn the keyswitch to align the 
number with the notch.

 

Notch position 4 is shown.

Make sure the DIN rail locking 
screw is in the horizontal position.

44229

Summary of Contents for 1734-OE4C























Reviews:

No comments