Allen-Bradley 1606-XLB480E Manual Download Page 15

Rockwell Automation Publication 1606-RM104A-EN-P - July 2020

15

           

Environment

Switching Frequencies

PFC converter 

80...130 kHz 

Input voltage and load dependent 

Main converter 

75...180 kHz 

Output voltage and load dependent 

Auxiliary converter  60 kHz 

Fixed frequency 

Attributes

Values

Notes

Operational temperature 

-25…+70 °C (-13…+158 °F) 

Operational temperature is the same as the ambient or surrounding 
temperature and is defined as the air temperature 2 cm (0.79 in.) 
below the unit. 

Storage temperature 

-40…+85 °C (-40…+185 °F) 

For storage and transportation 

Output derating 

12 W/°C (12 W/1.8 °F),
30 W/1000 m (30 W/3281 ft),
or 5 °C/1000 m (9 °F/3281 ft)

Between 55…70 °C (131…140 °F)
For altitudes >2000 m (6560 ft), see 

Figure 19

 

The derating is not hardware-controlled. You have to take this into consideration to stay below the 
derated current limits in order not to overload the unit. 

Humidity 5...95% 

r.h. According to IEC 60068-2-30 

Atmospheric pressure 

110…54 kPa 

See 

Figure 19

 for details 

Altitude 

Up to 5000 m (16,400 ft) 

See 

Figure 19

 for details 

Overvoltage category 

II 

According to IEC 60664-1, for altitudes up to 5000 m (16,400 ft)

Impulse withstand voltages 

4 kV (according to overvoltage 
category III) 

Input to PE According to IEC 60664-1, for altitudes up to 2000 m 
(6560 ft)

Degree of pollution 

According to IEC 60664-1, not conductive 

Vibration sinusoidal 

2…17.8 Hz: ±1.6 mm (0.06 in.);
17.8…500 Hz: 2 g (19.61 m/s

2

)

2 hours / axis 

According to IEC 60068-2-6 

Shock 

30 g 6 ms, 20 g 11 ms
3 bumps per direction,
18 bumps in total 

According to IEC 60068-2-27 

Shock and vibration are tested in combination with DIN rails according to EN 60715 with a height of 15 
mm (0.59 in.) and a thickness of 1.3 mm (0.05 in.) and standard orientation.

LABS compatibility 

As a rule, only non-silicon precipitating materials are used. The unit conforms to the LABS criteria and is 
suitable for use in paint shops. 

Corrosive gases 

Tested according to ISA-71.04-1985, Severity Level G3 and IEC 60068-2-60 Test Ke Method 4 for a 
service life of 10 years min in these environments. 

Audible noise 

Some audible noise may be emitted from the power supply during no load, overload, or short circuit. 

Figure 18 - Output current vs. ambient temp.

Figure 19 - Output current vs. altitude

0

0

+70 °C

20 A

+55

Allowed Output Current at 24V

12.5 A

Ambient Temperature

-25

 

2000 m

5000 m

18.8 A

16.3 A

20.0 A

Altitude

Allowed Output Current at 24V

B

A

AP

*)

80 kPa

54 kPa

110 kPa

0 m

*) Atmospheric pressure

A... Tamb < 45 °C
B... Tamb < 55 °C

4000 m

62 kPa

 

Summary of Contents for 1606-XLB480E



























Reviews: