manualshive.com logo in svg

Alinco DJ-196, Instruction Manual

Share
Download
Alinco DJ-196 Instruction Manual Download Page 17

    ….. Downward…….Upward…………

   ……. TP-0FF….. TP-1…… TP-4…… TP-15……….

   ……………………………………………………….

   The setting is available up to max. 15 seconds.

[No.8] DTMF WAIT time

1.   [DWT-01] appears on the LCD.

2.  Rotate the dial, and the display toggles as shown below.  Then the DTMF WAIT

   time will be changed.

3.  ** shows the current DTMF WAIT time.

   The initial setting is 0.1 second, and [DWT-01] appears on the LCD.

4.  Rotate the dial to change the DTMF WAIT time.

   ……Downward…………………..Upward……………

   …..DWT-01….DWT-04……DWT-07….. DWT-10 ……

   …………………………………………………………..

[No.9] DTMF Burst/Pause Time

1.   [DP-60] appears on the LCD.

2.  Rotate the dial, and the display toggles as shown below.  Then the DTMF

   burst/pause time will be changed.

3.  ** shows the current DTMF burst/pause time.

   The initial setting is 60 msec, and [DP-60] appears on the LCD.

4.  Rotate the dial to change the DTMF burst/pause time.

   …….Downward……………Upward………………...

   ……..DP-60 …..DP-80 ……DP-160……DP-200……..

   …………………………………………………………

[No.10] The First Digit Burst Time of DTMF

1.  [DB-60] appears on the LCD.

2.  Rotate the dial, and the display toggles as shown below.  Then the first digit of

   DTMF burst time will be changed.

3.  ** shows the current the first digit of DTMF burst time.

   The initial setting is 60 msec, [DB-60] appears on the LCD.

4.  Rotate the dial to change the first digit of DTMF burst time.

   ….Downward……Upward…………………………..

   …..DB-60……DB-80…… DB-160….. DB-200……

   ………………………………………………………

[No.11] Burglary Alarm Function

1.  [SCR-OF] appears on the LCD.

2.  Rotate the dial, and the display toggles as shown below.  Then the ON/OFF of the

   burglary alarm function is switched.

   ………..Downward…………Upward……………

   ………..SCR-OF……….. SCR-ON………………

   …………………………………………………….

[No.12] External Terminal Controller Output

1.  [EXP-OF] appears on the LCD.

2.  Rotate the dial, and the display toggles as shown below.   The ON/OFF of the

   controller output to external terminal will be switched repeatedly.

   ……Downward……Upward………….

   ……….EXP-OF…… EXP-ON……….

   …………………………………………

[No.13] Mosquito Repel Sound Function

1.  [MRS-OF] appears on the LCD.

Summary of Contents for DJ-196



















Reviews:

No comments

Brands by name

Popular brands

Load more brands