background image

70

  |  Removing 

the 

Speakers

Removing the Speakers

 

WARNING:  

Before working inside your computer, read the safety 

information that shipped with your computer and follow the steps in 
"Before You Begin" on page 9. For additional safety best practices 
information, see the Regulatory Compliance Homepage at dell.com/
regulatory_compliance. 

Prerequsites

1

Remove the battery pack. See "Removing the Battery Pack" on page 12.

2

Remove the compartment door. See "Removing the Compartment Door" on page 14.

3

Remove the center control cover. See "Removing the Center Control Cover" on 
page 41.

4

Remove the keyboard. See "Removing the Keyboard" on page 45.

5

Remove the power button board. See "Removing the Power Button Board" on 
page 55.

6

Remove the display assembly. See "Removing the Display Assembly" on page 57.

7

Remove the status light board. See "Removing the Status Light Board" on page 61.

8

Remove the palm rest assembly. See "Removing the Palm Rest Assembly" on 
page 64.

Procedure

1

Disconnect the speakers cable from the connector on the system board.

2

Note the speakers cable routing and remove the cable from the routing guides on the 
computer base.

3

Remove the screws that secure the speakers to the computer base.

4

Lift the speakers along with the cable off the computer base.

41

Summary of Contents for Alienware M17x R4

























































































Reviews: