3
www.observint.com
© 2016, 2017 Observint Technologies. All rights reserved.
ALI-NZ6022M Add-on Camera Installation
ALI-NZ6022M add-on camera includes the following:
•
1080P WDR 3.7 mm Right Angle Pinhole camera
•
Decorative cover
•
Straight mounting bracket
•
Tilt mounting bracket
•
Foam pads (2)
Foam pads (2)
Tilt mount
bracket
Decorative cover
Straight mounting bracket
A bracket and hardware is provided to mount the camera assembly flat on a surface, on a surface using the
tilt-mount bracket, or behind a surface (concealed) with camera visibility through a peep hole. The ALI-
NZ60 Base Station module can be secured to a surface, or supported by a hanger (hanger not provided).
Mounting the camera on a surface
To mount the camera on a surface:
1.
Determine the best location for the camera. Note that when mounted on a surface, the camera
points out perpendicular to the surface and has a view angle of 57
˚
.
2.
Attach the camera to the surface with two screws. Depending on the surface, wall inserts may be
required. The mounting hardware provided is adequate for most surfaces.
Cover
Camera
3.
Push the cover onto the camera. The cover will snap into place.
4.
Route the cable to the location where the ALI-NZ60 Base Station module will be located.
Mounting the camera on a surface with the tilt-mount bracket
The tilt mount bracket is used to mount the camera on a vertical (wall) or horizontal (ceiling) surface where
tilting the camera provides a better field of view. To use the tilt-mount bracket to mount the camera:
1.
Determine the best location for the camera. The camera view angle is 65
˚
.
2.
Attach the tilt-mount bracket to the surface.
the hardware provided is adequate for most
installations.
3.
Attach the camera to the bracket with the two
screws provided.
4.
Route the camera cable to the ALI-NZ60
module and plug it into the
VIN1
connector.
5.
After adjusting the camera for the best field
of view, tighten the screws on the sides of the
tilt-mount bracket, and then attach the cover.
Tilt-mount bracket
Camera
Screw (2)
Mounting the camera behind a surface
To mount the camera behind a surface:
1.
Determine the best location for the camera. Note that when mounted on a surface, the camera
points out perpendicular to the surface.
2.
Drill a hole in the mounting surface for the camera lens. The hole should be large enough to not
obstruct the full view of the camera. Suggested hole sizes are shown below for different wall
thicknesses.
Camera (View angle)
Lens set back distance
from wall surface (in)
Hole size
(min. diameter in)
Drill (in)
ALI-NZ6022M (65
˚)
0.5
.637
11/16 (0.688)
0.75
.956
1.00.(1.00)
3.
Peal the protective paper off of one side of an adhesive foam strip and then align and apply it to the
face of the bracket. See the drawing below.
Adhesive foam
on surface
Camera
Hole
Bracket
Screw
4.
Press the camera into the back of the bracket, and then tighten the screw to secure it in place.
5.
Peal the protective paper from the front side of the adhesive foam on the bracket, and press the
bracket with the camera onto the surface, aligning the camera lens with the center of the hole.
6.
Plug the camera cable into the
VIN1
connector of the ALI-NZ60 module.
ALI-NZ6032M Add-on Camera Installation
ALI-NZ6032M add-on camera includes the following:
•
1080P WDR 2.8 mm Wide Angle Tube Camera
•
Tilt mount bracket with sleeve assembly
Tilt-mount
bracket assembly
Sleeve
This product also includes a junction box adapter plate for attaching the camera assembly onto a
junction box.
The ALI-NZ6032M camera sensor is usually mounted to a ceiling with the tilt-mount bracket and sleeve
assembly provided. To install the camera:
1.
Unscrew the tilt-mount bracket extension from the mounting base, and then lift off the mounting
base cover.
