background image

1

www.observint.com

ALI-NS402xR_CQ 

170717

12 Vdc Power  

connector  

Ethernet connector -   

PoE capable

Camera drop cables 

What’s in the box

Your camera includes the items shown below. 

Junction box  (top view)

Drill Template

Adapter plate

Weatherproof  

Ethernet  

Fitting

Mounting 

hardware

Security  

L-wrench

Step 1.  Install the camera

The camera includes hardware to install it directly to the Junction box provided, to a mounting surface 
(without the junction box), or to a double-gang electrical box using the adapter plate provided. When 
using the junction box, camera LAN and power drop cables can attach to extension cables inside the 
box. The camera with or without the junction box can be installed on a ceiling (horizontal surface) or 
wall (vertical surface). To install the camera: 
1. 

Remove the cover on the underside of the camera, and then install a microSD card. The card can 
have a capacity up to 128GB. Reinstall the cover.

NOTE

The microSD card may need to be initialized before it can be used to record data. Refer to the 

ALIBI™ 

IP Camera Firmware Version .. User Manual

 provided at 

AlibiSecurity.com/resources

 for 

instructions to initialize the card. 

2. 

Mount the camera in one of the following ways:  

To mount the camera using the Junction box 

1. 

Determine the best fasteners for securing the Junction box to mounting surface. The mounting 
hardware provided is suitable for most surfaces. 

2. 

Remove the junction box from the camera assembly by loosing the four captive screws. 

3. 

Attach the drill template to the surface. Mark the location of the Junction box mounting screw 
holes. If routing extension cables for the LAN, power, alarm devices, etc. through the mounting 
surface, mark the location for that hole too. 

NOTE

: If installing the box onto a wall, observe 

the orientation for TOP and BOTTOM orientation markings inside the box and on the camera 
mounting base, and orient the drill template properly. 

Mounting surface

Orientation mark

Mounting base screws (4)

Junction box mounting screws (4)

Drill template

Safety cable

Junction box

Camera

4. 

Drill holes in the mounting surface for the mounting screws and extension cables (if necessary). 

5. 

Secure the Junction box to the mounting surface using appropriate fasteners. 

ALI-NS4022R, ALI-NS4023R,  

ALI-NS4025R, ALI-NS4028R  

IP Bullet Cameras  

Quick Installation Guide

This document guides you through the basic steps to install and configure the ALI-NS4022R,  
ALI-NS4023R, ALI-NS4025R and ALI-NS4028R IP bullet cameras. These cameras feature: 

• 

Supports H.265+ / H.265 / H.264OVC / H.264 / MJPEG compression

• 

120 dB Wide Dynamic Range

• 

Full Frame Illumination Smart IR array, 

• 

Supports onboard storage up to 128GB Max microSD (card not included)

• 

IP67 ratred, 

22 °F ~ 140 °F temperature range

• 

ONVIF Profile S & Profile G, PSIA, CGI, ISAPI

For more information, refer to these documents - available from your equipment vendor:

• 

ALIBI™ Tools Utility Installation and User Manual

• 

ALIBI™ Witness App for Android Quick Start Guide

• 

ALIBI™ IP Camera Firmware Version x.x User Manual

 provided at:  

AlibiSecurity.com/resources

Camera body

Lens

Articulated  

mounting  

bracket

Junction box assembly 

(see detail below)

Sun Shield

Camera mounting base

Access to microSD slot  

and Reset button*

To restore the camera with its default configuration (including user name, password, IP address, etc.) press and hold the 

Reset  

    button for 10 s when the camera is power on or rebooting. 

Top (up)

Bottom (down)

Conduit port (2)

Mounting screw 

hole (4)

Hole for camera 

mounting screw (4)

Cable access  

through mounting 

surface

Camera base  

locator pins

Junction box detail

Reviews: