1
www.observint.com
ALI-CD1720_CQ
8/27/15
What’s in the box
•
Camera assembly
•
Mounting screws and wall inserts
•
This manual
•
Drill template
What you need
•
12 Vdc power source. See Specifications for
voltage and wattage requirements.
•
Tools and additional fasteners (may be required)
for mounting the camera
•
Video and power extension cable
•
HD-TVI video setup monitor (optional)
Installation
Before installation:
•
Check the specification of the products for the installation environment.
•
Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
•
To avoid fire or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the
Specifications
section.
During installation:
•
Camera Lens
: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
array shield becomes soiled, clean it only with approved products. See the
Cleaning
section.
•
Camera drop cable
: The camera drop cable includes two connectors:
—
HD-TVI Video BNC connector
: For transmission of the HD-TVI signal across a coax (75 Ω)
extension cable.
—
Power connector:
When applying Vdc power, observe the power polarity. See the picture
above for the connector polarity configuration.
1.
Using the drill template provided with your camera, mark the location of the screws that anchor the
base plate to the mounting surface. If you are routing the drop cable through base, also mark the
position of the hole for the drop cable.
2.
Drill holes for the screws that anchor the base to the ceiling. The mounting hardware provided is
appropriate for most surfaces. However, depending on the surface materials, more appropriate
fasteners may be required.
3.
Drill a 5/8” hole for the drop cable, if necessary. The drop cable can be routed through the mounting
surface, or through a cable channel in the mounting plate.
4.
Route video and power extension cables from the camera to the video recorder and power source. If
using a video and power combo-cable, make sure the end with the male power plug is toward the
camera.
5.
Separate the mounting plate from the camera assembly:
a.
Hold the mounting plate, and then turn
the locking bezel counter clockwise
about 1/8 turn as shown in the picture
below.
b.
Lift off the locking bezel, and then
unclip and remove the housing.
c.
Remove the camera module.
Camera
module
Mounting
plate
Housing
Locking
bezel
ALI-CD1720 Series HD-TVI Turret
Cameras Quick Installation Guide
For Products
: ALI-CD1720E, ALI-CD1720G
The ALIBI ALI-CD1720 series turret cameras include a high sensitivity sensor and advanced circuit design
technology. They feature high resolution, low image distortion and low noise features which makes them
suitable for surveillance and image processing systems.
Features
•
HD-TVI technology transmits zero latency HD video resolution over coax cabling
•
1280 x 720 (720p @ 30 fps) HD video for sharp, detailed images
•
2.8 mm wide angle lens (ALI-CD1720G only) captures images over large areas
•
Built-in 24 LEDs enables the camera to see up to 65 ft in the dark
•
Smart IR technology reduces over-exposure of the IR LEDs at the center of the image
•
True day/night (ICR) captures sharp, clear images in low light and at night
•
-40°F ~ 140°F extreme temperature operating range
•
IP66 weather-rated ABS housing
Mounting
plate (inside)
IR array
Lens
Camera
module
Light
sensor
Housing
Locking
bezel
ALI-CD1720E camera assembly
Mounting
plate (inside)
IR array
Lens
Camera
module
Light
sensor
Housing
Locking
bezel
ALI-CD1720G camera assembly
Power
Connector
HD-TVI Video
BNC Connector
ALI-CD1720 series camera drop cable connectors
