ALGE-Timing Mobile Timing MT1, Manual, Page: 13 / 16

Share

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Page: 13 / 16

ALGE-Timing Mobile Timing MT1 Manual Download Page 13

Manual

Mobile Timing MT1

- 13 -

Fill out the serial number of your device and click “CONTINUE”

Then enter the PIN code, which will be displayed on the MT1 to proof that it is your device.
With each new MT1 device you will get 2000 timing points (TP). This TP you will need for
event creation (150TP) and data transmission. If you want to transfer this TP to your account,
you have select this here. Then click “CONTINUE”. Now you can use your MT1 device in the

alge-results.com

platform.

There are three possible actions for a device:

First action is edit, where you can change the device name, time zone and synchronization
configuration and delay time. Under “trigger” you can see the received impulses.
Second action is re-read. That action will read the current status of the MT1 device.
Third action will remove the device from your account.

Note:
If you want to pass your device to another timer, you have to remove it from your account first.
A device can only belong to one account at a time.

To get some more information about the

alge-results.com platform

we provide an extra manual

at the

alge-timing.com website

5.3.1 Evaluation software

If your evaluation software can work with serial data and supports the communication protocol,
(Timy series or TDC 800x series, daytime format) it can be used to read the timestamps direct-
ly via USB interface.

5.3.2 Time.NET Connector

The Time.NET Connector is a software to connect the MT1 system with an evaluation soft-
ware. There are many connection possibilities:

«
...
11
12
13
14
15
...
»

Summary of Contents for Mobile Timing MT1

















Reviews:

No comments