ALFAtron ALF-10XUSB2C User Manual Download Page 32

ALFATRON ALF-3XUSB2C

 

 

 

31 

 

1.10.2 Replace this product with a direct replacement or with a similar product deemed by the Company 
to perform substantially the same function as the original product; or 
1.10.3 Issue a refund of the original purchase price less depreciation to be determined based on the age 
of the product at the time remedy is sought under this limited warranty. 
1.11 The Company is not obligated to provide the Customer  with a substitute unit during the limited 
warranty period or at any time thereafter. 
1.12 If this product is returned to the Company this product must be insured during shipment, with the 
insurance and shipping charges prepaid by the Customer. If this  product is returned uninsured, the 
Customer assumes all risks of loss or damage during shipment. The Company will not be responsible for 
any costs related to the removal or re-installation of this product from or into any installation. The 
Company will not be responsible for any costs related to any setting up this product, any adjustment of 
user controls or any programming required for a specific installation of this product. 
1.13 Please be aware that the Company’s products and components have not been tested  with 
competitor’s products and therefore the Company cannot warrant products and/or components used in 
conjunction with competitor’s products. 
1.14 The appropriateness of the goods for the purpose intended is only warranted to the extent that the 
goods are used in accordance with the Company’s installation, classification and usage instructions. 
1.15 Any claim by the Customer which is based on any defect in the quality or condition of the goods or 
their failure to correspond with specification shall be notified in writing to the Company within 7 days of 
delivery or (where the defect or failure was not apparent on reasonable inspection by the Customer) 
within a reasonable time after discovery of the defect or failure, but, in any event, within 6 months of 
delivery. 
1.16 If delivery is not refused, and the Customer does not notify the Company accordingly, the Customer 
may not reject the goods and the Company shall have no liability and the Customer shall pay the price as 
if the goods had been delivered in accordance with the Agreement. 

1.17 THE MAXIMUM LIABILITY OF THE COMPANY UNDER THIS LIMITED WARRANTY SHALL 

NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT

 

 

Summary of Contents for ALF-10XUSB2C

































Reviews: