manualshive.com logo in svg

Alesis POWER AMPLIFIER RA150, Reference Manual

Share
Download
Alesis POWER AMPLIFIER RA150 Reference Manual Download Page 33

Specifications

RA150/300/500 Reference Manual

31

Reference 500

Size

18.9" W x 5.63" H x 10.71" D

 

      

(480mm x 143 mm x 272 mm)

Rack units

3 RU height

Weight

28.5lbs = 13.0Kg

Rated output, per channel

4 ohms @ 1kHz, .02% THD+N

250 watts RMS per channel

8 ohms @ 1kHz, .05% THD+N

150 watts RMS per channel

8 ohms, bridged mono mode

500 watts RMS

Signal to Noise Ratio

105dB, 22Hz-22kHz bandwidth referenced to rated output

Frequency Response

10Hz – 70kHz +0, -3dB

Damping Factor

200

Slew Rate

60 V/µs (two channel), 120 V/µs (bridged mono)

Input Sensitivity

+4dBu (1.23 V) for rated output with input control at maximum

Maximum input level

+26 dBu

Input impedance

20k 

Ω

, balanced, 10 k

Ω

 unbalanced

Crosstalk

-85dB, 1kHz

All measurements done over a 20Hz-22,000Hz range with 1KHz sine wave at  Full Scale, except for the dynamic
range which was done with a -60dBFS 1KHz sine wave.

Dimensioned drawings

RA150

Summary of Contents for POWER AMPLIFIER RA150







































Reviews:

No comments

Brands by name

Popular brands

Load more brands