Alemlube BR50010D Owner Technical Manual Download Page 3

Visit our website at  

www.alemlube.com.au

 or 

www.alemlube.co.nz

NSW/ACT
TEL: (02) 9677 1555

FAX: (02) 9675 1155

QLD/PNG
TEL: (07) 3204 9166

FAX: (07) 3204 1224

VIC/TAS
TEL: (03) 8787 8288

FAX: (03) 8787 8266

WA
TEL: (08) 9302 4199

FAX: (08) 9303 2095

SA/NT
TEL: (08) 8241 7111

FAX: (08) 8241 7011

NZ
TEL: (09) 447 1007

FAX: (09) 447 1008

3

Danger Safety Barrier Reel

OWNER’S TECHNICAL MANUAL

BR50010D

OPERATION

1.

  Check reel for correct operation by slowly pulling out warning tape. A”clicking” noise will be heard every half 

revolution of the drum.

2.

  To latch the reel, pull out the warning tape and allow it to retract after hearing the first, second or third click.

3.

  To unlatch, slowly pull out the warning tape until the”clicking”noise stops,then let cable retract until the cable 

stopper rests against the cable guide.

4.

  If necessary, adjust spring tension on reel by adding or removing wraps of warning tape from spool, one wraps  

at a time, until desired tension is obtained. Add wraps to increase tension. Remove wraps to decrease tension.

5.

  Equipped with idle system to ensure safe use

Fixation Method

The BR50010D reel contains accessory package (including magnet, eye screw and expansion plug).  

The fixing method is various and flexible, and it is suitable for most working situation.

1.

  The fixing pin on the reel can be directly hooked into the slot hole, or the belt can be clamped with the pin after 

wrapping the object with a warning tape (see Figure 1).

2.

  The magnet is hung on the fixed pin. Through the magnet, the warning tape can be directly connected 

 

with the metal surface (see Figure 2).

3.

  The eye screw can be fixed on the wood board or trunk, and the fixing pin can be connected with it 

 

(see Figure 3).

4.

  The expansion plug is used together with the eye screw, and the fixing pin is connected to the wall 

 

(see Figure 4).

MAINTENANCE

Make sure the hose is in proper working order.

1.

  Clean the hose with a cloth dipped in warm water to remove dirt or deposits and ensure correct rewinding.

2.

  Do not use detergents or solvents which could prove incompatible with cable-winder materials.

3.

  Dismantling of the unit by unskilled personal could prove hazardous;the risk involved mainly concern  

the preloaded springs.

LIMITED WARRANTY

1.

  Alemlube warrants this hose reel against defects in material and craftsmanship, for a period of 12 months  

from date of purchase.

2.

  Alemlube’s liability is limited to replacement or repair of defective material within the warranty period,  

when returned freight prepaid to the distributor or their designated service depot.

3.

  The warranty dose not cover damage caused by accident, misuse or faulty installation.

4.

  The reel must be installed and maintained in compliance with the instructions.

Summary of Contents for BR50010D






Reviews: