background image

Operation, Maintenance and Installation Manual

2-Zone | Outdoor Alarm System, Type 4X

Alarm Systems

Control Panels

Float Switches

Leak Detection Systems

Page 1 of 6

Alderon Industries - Hawley, MN  |  218.483.3034  |  [email protected]  |  alderonind.com

P/N: QSG00307_Rev01

VersAlarm

 4X

Safety Guidelines

Before proceeding with the installation or operation of the product, make sure to read all instructions thoroughly, as well as 

complying with all federal, state and local codes, regulations and practices. The product must be installed by qualified 

personnel familiar with all applicable local electrical and mechanical codes. Refer to the National Electric Code (NFPA 70). 

Failure to properly install and test this product can result in personal injury or equipment malfunction.

1. DISCONNECT POWER when installing or servicing the product. Failure to disconnect all power sources could result in

  serious injury or death.

2. NEVER enter a flooded space without proper Personal Protective Equipment (PPE). Always wear dielectric rubber boots

  and other applicable protective equipment when water is on the ground or floor and you must service an energized pump,

  alarm system, or product.

3. DO NOT enter the water if the water level is higher than that of the protection your PPE offers or if your PPE is not

 watertight.

4. DO NOT use this product with or near flammable liquids.

5. DO NOT install this product in locations classified as hazardous or in explosive atmospheres as defined by any applicable

  electrical safety code.

Introduction

SPECIFICATIONS:

Primary Power

120VAC or 240VAC, 50/60 Hz

(voltage depends on model)

Secondary Power

9-10VDC, 200mA

Watts

3.0 Watts

Field Connection Sensor

9-10VDC, 1mA minimum

(signaling device)

Auxiliary Contacts

120VAC, 0.3A maximum

24VDC, 0.5A maximum

Normally Open; Single Pole, Single Throw

LEDs

Green 

(power and zone indicator)

Red 

(alarms)

Buzzer

5-30VDC, 95 dB @ 2-feet

Control Transformer

120VAC or 240VAC, 2.4VA

(voltage depends on model)

Battery Backup

Lithium 9VDC battery

(not included)

Enclosure

Thermoplastic

4 x 4 x 3 

(inches)

Type 4X, Outdoor

Lockable Latch

Certifications

CSA 

(US and Canada)

Three-Year Limited Warranty

Summary of Contents for VersAlarm 4X







Reviews: