6
507 Hydraulic Installation Tool
(HK480)
Alcoa Fastening Systems & Rings
D
ESCRIPTION
MAX OPERATING TEMP:
125° F (
51.7° C
)
MAX FLOW RATE:
2 gpm (
7.5 l/m
)
PULL CAPACITY:
75,500 lbs @ 5,700 psi
(
337 kN @ 393 bar
)
MAX PULL PRESSURE:
5,700 psi (
393 bar
)
MAX RETURN PRESSURE:
2,400 psi (
165 bar
)
STROKE:
2.5 inches (
6.3 cm
)
WEIGHT:
43 lbs (
19.5 kg
)
POWER SOURCE:
Huck POWERIG
®
Hydraulic Unit
HOSE KITS:
Use only genuine HUCK Hose Kits rated
@ 10,000 psi (
689.5 bar
) working pressure.
HYDRAULIC FLUID:
Hydraulic fl uid shall meet
DEXRON
®
III, DEXRON VI, MERCON
®
, Allison C-4
or equivalent Automatic Transmission Fluid (
ATF
)
specifi cations. Fire-resistant fl uid may be used if it
is an ester-based fl uid such as Quintolubric
®
HFD or
equivalent. Water-based fl uid shall NOT be used as
serious damage to equipment will occur.
DEXRON is a registered trademark of General Motors Corp.
MERCON is a registered trademark of Ford Motor Corp.
Quintolubric is a registered trademark of Quaker Chemical Corp.
S
PECIFICATIONS
15.5
(39.4)
9.6
(24.4)
2.7
(6.9)
6
(15.2)
Inches
(cm)
I
NCHES
(cm)
The Huck 507 inline Hydraulic Installation Tool
installs
C50L HUCKBOLT
®
Fasteners
and
HLC50L
HUCKLOK
®
Fasteners
. When equipped with the proper
(optional) nose assembly, it can install:
-32
(1” diameter) and
-36
(1-1/8” diameter) fasteners.
Each tool has a cylinder and piston assembly. A relief
valve, designed to relieve the hydraulic pressure at
both ends of the stroke, is situated near the piston.
The pintail ejector ejects broken pintails from the nose
assembly. The end of the piston rod is threaded, and
a nose adapter and retaining rings are included for
attaching nose assemblies.
The operating pressures for the 507 tool are:
•
PULL: 5400–5700 psi (
372–393 bar
) and
•
RETURN: 2200–2400 psi (
152–165 bar
)
as supplied by a Huck POWERIG
®
Hydraulic Unit,
models
940
and
918
—or an equivalent hydraulic unit.
The correct PULL and RETURN pressures are
important for the proper function of the tool and Nose
Assemblies, as well as for the safety of the operator.
Huck has available a gauge (P/N
T-124833CE
) for
checking hydraulic pressures; instructions for its use are
included with the gauge and the POWERIG.
UPDATING OLDER TOOLS
Changes were made to the 507 tool,
starting with serial
number 0847
. Replacement parts are still available for
the earlier models. If your tool’s serial number is lower
than 0847, Huck recommends that the tool be updated
to the current confi guration. Call your Technical Support
representative for the part numbers.
OPTIONAL ACCESSORY
A
Suspension Bracket
that alleviates operator fatigue
is available from Huck. When the bracket is used with
a balance spring suspension system, much of the
tool’s weight is supported. Contact Huck Customer
Service for the part number and availability. See
K
ITS
&
A
CCESSORIES
.
