Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 916

Page: 916 / 2018

Ethernet OAM Commands

page 25-4

OmniSwitch 6250 CLI Reference Guide

November 2009

Related Commands

MIB Objects

Dot1agCfmMd

dot1agCfmMdIndex

dot1agCfmMdFormat

dot1agCfmMdName

dot1agCfmMdLevel

dot1agCfmMdMhfCreation

dot1agCfmMdRowStatus

show ethoam

Displays the information of all the Management Domains (MD)
configured on the bridge.

show ethoam domain

Displays the information of a specific Management Domain config-
ured on the bridge.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 916 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: