Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 947

Page: 947 / 2018

Ethernet OAM Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 25-35

show ethoam

Displays the information of all the Management Domains (MD) configured on the bridge.

show ethoam

Syntax Definitions

N/A

Defaults

N/A

Platforms Supported

OmniSwitch 6250-Metro Models

Usage Guidelines

This command displays all the MAs for all the MDs.

Examples

-> show ethoam

System Configuration

Ethernet OAM system mac address: 00:D0:95:EC:84:B0,

Number of Maintenance Domains: 1

Maintenance Domain: esd.alcatel-lucent.com

Maintenance Association: alcatel-sales

Release History

Release 6.6.1; command was introduced.

Related Commands

output definitions

Ethernet OAM system mac
address

The MAC address of the Ethernet OAM system.

Number of Maintenance
Domains

The number of maintenance domains configured on the bridge.

Maintenance Domain

The name of the maintenance domain.

Maintenance Association

The name of the maintenance association.

ethoam domain

Creates an Ethernet domain.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 947 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: