manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1497 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1497

OmniSwitch CLI Reference Guide

November 2009

page 39-1

39   QoS Policy Commands

This chapter describes CLI commands used for policy management in the switch. The Quality of Service 
(QoS) software in the switch uses policy rules for classifying incoming flows and deciding how to treat 
outgoing flows. A policy rule is made up of a policy condition and a policy action. Policy rules may be 
created on the switch through CLI or SNMP commands, or they may be created through the PolicyView 
GUI application on an attached LDAP server.

Note. 

Rules created through PolicyView cannot be modified through the CLI; however, you can create 

policies in the CLI that take precedence over policies created through PolicyView.

Refer to 

Chapter 38, “QoS Commands,”

 for information about commands used to configure QoS software.

MIB information for the QoS policy commands is as follows:

Filename

: alcatelIND1Qos.mib

Module

ALCATEL-IND1-QoS-MIB

Important Note

. Some of the commands listed here are not currently supported on one or more plat-

forms. See command descriptions in this chapter and check release notes for information about commands 
that are not supported.

The QoS Policy commands are listed here:

Policy commands

policy rule
policy validity period
policy condition
policy action
show policy action
show policy condition
show active policy rule
show policy rule
show policy validity period

Group commands

policy network group
policy service
policy service group
policy mac group
policy port group
policy map group
show policy network group
show policy mac group
show policy port group
show policy map group
show policy service
show policy service group

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments