Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1459

Page: 1459 / 2018

QoS Commands

OmniSwitch CLI Reference Guide

November 2009

page 38-31

qos flush

Deletes all pending policy information. This command is different from

qos revert

, which returns the

pending policy configuration to its last applied settings.

qos flush

Syntax Definitions

N/A

Defaults

N/A

Platforms Supported

OmniSwitch 6250

Usage Guidelines

•

If you enter this command, the pending policy configuration is completely erased. If you then enter

qos

apply

, the erased configuration

overwrites the applied policies and you will erase all of your policy

configuration

Note.

Do not use this command unless you want to erase all of your policy configuration and start config-

uring new policies.

•

Use the

qos revert

command to return the pending policy configuration to its last applied value.

•

Policy configuration includes the following commands:

Examples

-> qos flush

Release History

Release 6.6.1; command was introduced.

base commands

policy rule
policy network group
policy service
policy service group

policy mac group
policy port group
policy condition
policy action

«
...
1457
1458
1459
1460
1461
...
»

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1459 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: