Alcatel-Lucent OAW-AP204, Installation Manual

Page: 2 / 2

OAW-AP200 Series Wireless
Access Point
Installation Guide
OAW-AP200 Series Wireless Access Point | Installation Guide
Part Number 0511620-01 | April 2014
Contacting Alcatel-Lucent
Web Site Support
Main Site http://www.alcatel-lucent.com/enterprise
Support Site https://service.esd.alcatel-lucent.com
Support Email esd.support@alcatel-lucent.com
Telephone Support
North America 1-800-995-2696
Latin America 1-877-919-9526
Europe +800 00200100 (Toll Free)
or 1-650-385-2193
Asia Pacific +65 6240 8484
Worldwide 1-818-878-4507
Copyright
Copyright © 2014 Alcatel-Lucent. All rights reserved.
Specifications in this manual are subject to change without notice.
Originated in the USA.
Trademarks
AOS-W, Alcatel 4302, Alcatel 4304, Alcatel 4306, Alcatel 4308, Alcatel 4324, Alcatel 4504, Alcatel 4604, Alcatel
4704, Alcatel 4550, Alcatel 4650, Alcatel 4750, Alcatel 6000, OAW-AP41, OAW-AP68, OAW-AP60/61/65,
OAW-AP70, OAW-AP80, OAW-AP92/93, OAW-AP104/105, OAW-AP114/115, OAW-AP120/121, OAW-AP124/
125, OAW-RAP155, OAW-AP175, OAW-IAP92/93, OAW-AP204/205, OAW-AP214,/215, OAW-AP224/225,
OAW-AP274/275, OAW-RAP2, OAW-RAP5, and Omnivista 3600 Air Manager are trademarks of Alcatel-Lucent in
the United States and certain other countries.
Any other trademarks appearing in this manual are the property of their respective companies.
Legal Notice
The use of Alcatel-Lucent switching platforms and software, by all individuals or corporations, to terminate Cisco
or Nortel VPN client devices constitutes complete acceptance of liability by that individual or corporation for this
action and indemnifies, in full, Alcatel-Lucent from any and all legal actions that might be taken against it with
respect to infringement of copyright on behalf of Cisco Systems or Nortel Networks."
Figure 7 Attaching the Ceiling Rail Adapter
4. If necessary, connect the console cable to the console port on the back of the
AP.
5. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots
at approximately a 30-degree angle to the ceiling tile rail (see Figure 8 ). Make
sure that any cable slack is above the ceiling tile.
6. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks
into place on the ceiling tile rail.
Figure 8 Mounting the AP
7. On the OAW-AP204, install the external antennas according to the
manufacturer’s instructions, and connect the antennas to the antenna
interfaces on the AP.
Connecting Required Cables
Install cables in accordance with all applicable local and national regulations and
practices.
Verifying Post-Installation Connectivity
The integrated LEDs on the AP can be used to verify that the AP is receiving
power and initializing successfully (see
Table 1 ). Refer to the AOS-W Quick Start
Guide for further details on verifying post-installation network connectivity.
Configuring the OAW-AP200 Series
AP Provisioning/Reprovisioning
Provisioning parameters are unique to each AP. These local AP parameters are
initially configured on the switch which are then pushed out to the AP and stored
on the AP itself. Alcatel recommends that provisioning settings be configured via
the AOS-W Web UI only. Refer to the
AOS-W User Guide for complete details.
AP Configuration
Configuration parameters are network or switch specific and are configured and
stored on the switch. Network configuration settings are pushed out to the AP(s)
but remain stored on the switch.
Configuration settings can be configured via the AOS-W Web UI or AOS-W CLI.
Refer to their respective guides for further details: the
AOS-W User Guide .
Product Specifications
Electrical
 Ethernet:
 1x 10/100/1000 auto-sensing Ethernet RJ-45 Interface
 MDI/MDX
 IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)
 Power over Ethernet (802.3af compliant), 48V DC (nominal) and 56V DC
(maximum)/350mA (see
Figure 6 for pin configuration)
 Power:
 12 VDC power interface, supports powering through an AC-to-DC power adapter
 POE support on Ethernet port: 802.3af-compliant POE sourcing devices
F
or additional specifications on this product, please refer to the data sheet. The data sheet
can be found at http://www.alcatel-lucent.com/enterprise .
Proper Disposal of Alcatel Equipment
For the most current information about Global Environmental Compliance and Alcatel
products, see our website at
http://www.alcatel-lucent.com/enterprise .
China RoHS
Alcatel products also comply with China environmental declaration
requirements and are labeled with the “EFUP 10” label shown at the left.
European Union RoHS
Alcatel products also comply with the EU Restriction of
Hazardous Substances Directive 2011/65/EC (RoHS). EU RoHS
restricts the use of specific hazardous materials in the
manufacture of electrical and electronic equipment. Specifically,
restricted materials under the RoHS Directive are Lead (including Solder used in printed
circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some
Alcatel products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in
solder used in printed circuit assemblies). Products and packaging will be marked with
the “RoHS” label shown at the left indicating conformance to this Directive.
India RoHS
This product complies with RoHS requirements as prescribed by E-Waste (Management &
Handling) Rules, governed by the Ministry of Environment & Forests, Government of
India.
Waste of Electrical and Electronic Equipment
Alcatel products at end of life are subject to separate collection and
treatment in the EU Member States, Norway, and Switzerland and
therefore are marked with the symbol shown at the left (crossed-out
wheelie bin). The treatment applied at end of life of these products in
these countries shall comply with the applicable national laws of
countries implementing Directive 2002/96EC on Waste of Electrical
and Electronic Equipment (WEEE).
Safety and Regulatory Compliance
Alcatel provides a multi-language document that contains country-specific restrictions
and additional safety and regulatory information for all Alcatel access points. This
document can be viewed or downloaded from the following location: at
http://
www.alcatel-lucent.com/enterprise.
Regulatory Model Names
The following regulatory model names apply to the OAW-AP200 Series:
 OAW-AP204: APIN0204
 OAW-AP205: APIN0205
정소출력 무선기기
(
무선데이터통신시스템용 무선기기
)
FCC
This device is electronically labeled. To view the FCC ID:
1. Log into the switch WebUI.
2.
Navigate to
Maintenance > Switch > About
.
FCC Class B Part 15
This device complies with Part 15 of the Federal Communications Commission (FCC)
Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2.
This device must accept any interference received, including interference that may
cause undesired operation
.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
manufacturer’s instructions, may cause interference harmful to radio communications.
If this equipment does cause interference, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
 Consult the dealer or an experienced radio or TV technician for help.
Complies with the Class B limits for radio noise emissions as set out in the interference-
causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.
Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le
materiel brouilleur du Canada.
Users are advised that high power Radars are allocated as primary users of the bands
5250-5350 MHz and 5650-5850 MHz and these Radars could cause interference and/or
damage to Licensed Exempt WLAN devices.
해당무선설비는 전파혼신의 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다
.
EU Regulatory Conformance
This product is CE marked according to the provisions of the R & TTE
Directive (1999/5/EC) - CE(!). Alcatel-Lucent hereby declares that the APIN0204 /
APIN0205 device models are in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC -CE(!)
The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at
http://www.alcatel-lucent.com/enterprise.
Canada
(i)les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement
pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350
MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.;
(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825
MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et
non point à point, selon le cas.
De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute
puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les
bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du
brouillage et/ou des dommages aux dispositifs LAN-EL.
Medical
1. Equipment not suitable for use in the presence of flammable mixtures.
2. End product system, including power supply, must be evaluated to IEC 60601-1-1 and
IEC 60601-1 by the end user.
3. Wipe with a dry cloth, no additional maintenance required.
4. No serviceable parts, the unit must be sent back to the manufacturer for repair.
5. No modifications are allowed without Alcatel approval.
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大
功率或變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有
干擾現象時，應立
?
停用，
?
改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電
機設備之干擾。
Korean EMC Class B Warning
이 기기는 가정용
(B
급
)
전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며
,
모든 지역
에서 사용할 수 있습니다
.
AP-204_04
If a power adapter other than the one provided by Alcatel Networks is used
in the US or Canada, it should be cULus (NRTL) Listed, with an output
rated 12 VDC, minimum 1.5A, marked “LPS” or “Class 2,” and suitable for
plugging into a standard power receptacle in the US and Canada.
!
RF Radiation Exposure Statement: This equipment complies with FCC
RF radiation exposure limits. This equipment should be installed and
operated with a minimum distance of 7.9 inches (20 cm) between the
radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter
must not be co-located or operating in conjunction with any other antenna
or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this
device is restricted to indoor use to reduce the potential for harmful
interference with co-channel Mobile Satellite Systems.
10
᳝↦᳝ᆇ⠽䋼ໄᯢ
Hazardous Materials Declaration
᳝↦᳝ᆇ⠽䋼៪ܗ㋴
(Hazardous Substance)
䚼ӊৡ⿄
(Parts)
䪙
3E
∲
+J
䬝
&G
݁Ӌ䫀
&U
໮⒈㘨㣃
3%%
໮⒈Ѡ㣃䝮
3%'(
⬉䏃ᵓ
(
PCA Boards)
h ƻ ƻ ƻ ƻ ƻ
ᴎẄ㒘ӊ
(
Mechanical Sub-Assemblies)
h ƻ ƻ ƻ ƻ ƻ
ƻ˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼
SJ/T11363-2006 ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ
Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is
below the relevant threshold of the SJ/T11363-2006 standard.
h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛޚ㾘ᅮⱘ䰤䞣㽕∖DŽ
Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials
in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼DŽ
This table shows where these substances may be found in the supply chain of electronic information
products, as of the date of sale of the enclosed product.
ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ
՟བ⬉∴ऩܗ῵ഫ䌈೼݊ѻકϞ
ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟ݠЁ᠔㾘ᅮⱘᴵӊϟᎹ԰
The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are
per the symbol shown here. The Environment- Friendly Use Period is valid only when the
product is operated under the conditions defined in the product manual.
!
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
Aucune émission n’est permise dans la bande 5 600-5 650 MHz. Jusqu’à
nouvel avis, les dispositifs visés par la présente annexe ne doivent pas être
en mesure d’émettre dans la bande 5 600-5 650 MHz, afin de protéger les
radars météorologiques d’Environnement Canada exploités dans cette
bande.
!
Déclaration concernant l'exposition aux rayonnements de
radiofréquences :
cet équipement est conforme aux normes d'Industrie
Canada relatives aux limites d'exposition humaine aux radiofréquences. Cet
équipement doit être installé et utilisé à une distance minimale de 20 cm (7,9
pouces) entre le dispositif de radiocommunication et votre corps dans les
gammes de 2,4 GHz et 5 GHz. Cet émetteur-récepteur ne doit pas être
placé à proximité immédiate d'une autre antenne ou un d'autre émetteur-
récepteur, ou ne doit pas être utilisé conjointement avec ceux-ci.