Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 432

Page: 432 / 444

Tools Commands

Page 432

7750 SR OS Interface Configuration Guide

Tools Commands

redundancy

Syntax

redundancy

Context

tools>dump

Description

This command enables the context to dump redundancy parameters.

multi-chassis

Syntax

multi-chassis

Context

tools>dump>redundancy

Description

This command enables the context to dump multi-chassis parameters.

mc-ring

Syntax

mc-ring

Context

tools>dump>redundancy>multi-chassis

Description

This command dumps multi-chassis ring data.

sync-database

Syntax

sync-database

[

peer

ip-address

] [

port

port-id

lag-id

] [

sync-tag

sync-tag

] [

application

{

dhcps

igmp

igmp-snooping

srrp

sub-mgmt

mld-snooping|mc-ring

}] [

detail

] [

type

{

alarm-deleted|local-deleted

}]

Context

tools>dump>redundancy>multi-chassis

Description

This command dumps multi-chassis sync database information.

Parameters

peer

ip-address

—

Dumps the specified address of the multi-chassis peer.

port

port-id

—

Dumps the specified port ID of the multi-chassis peer.

port

lag-id

—

Dumps the specified Link Aggregation Group (LAG) on this system.

sync-tag

sync-tag

—

Dumps the synchronization tag used while synchronizing this port with the

multi-chassis peer.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands