Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 40

Page: 40 / 444

Port Features

Page 40

7750 SR OS Interface Configuration Guide

Figure 6: MLPPP Class Queue Thresholds for In-Profile and Out-of-Profile Packets

Table 8

and

Figure 7

provide the details of the class queue scheduling parameters.

Figure 7: MLPPP Class Queue Scheduling Scheme

MDA Class Queue

Service Egress SAP Queue

max

out of profile

(oop)

Scheduler

(pir, cir)

Fabric

mbs high-prio-

only

out

cbs

Table 8:

MLPPP Class Queue Scheduling Parameters

WRR Parameters

4-class MLPPP
Egress QoS Profile

MIR

Profile 1

85%

<1%

66%

33%

Profile 2

90%

<1%

89%

10%

Profile 3

85%

<1%

87%

12%

Class0

Class1

Class2

Class3

> MIR

wrr

t p

rity

yes

> 100%

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Search results

Summary of Contents for 7750 SR OS

Reviews:

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 40 / 444

Search results

Summary of Contents for 7750 SR OS

Reviews: