Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 238 | Manualshive

Page: 238 / 444

background image

Configuration Commands

Page 238

7750 SR OS Interface Configuration Guide

Parameters

seconds —

The server timeout period in seconds.

Values

1 — 300

transmit-period

Syntax

transmit-period

seconds

no transmit-period

Context

config>port>ethernet>dot1x

Description

This command configures the period after which the 7750 SR sends a new EAPOL request message.

The

no

form of this command returns the value to the default.

Default

30

Parameters

seconds —

The server transmit period in seconds.

Values

1 — 300

down-when-looped

Syntax

down-when-looped

Context

config>port>ethernet

Description

This command configures Ethernet loop detection attributes.

dot1x

Syntax

dot1x

Context

config>port>ethernet

Description

This command enables access to the context to configure port-specific 802.1x authentication
attributes. This context can only be used when configuring a Fast Ethernet, gigabit or 10Gig
EthernetFast Ethernet, gigabit or 10Gig EthernetFast Ethernet or gigabit Ethernet LAN ports on an
appropriate MDA.

keep-alive

Syntax

keep-alive

timer

no keep-alive

Context

config>port>ethernet>dwl

«
...
236
237
238
239
240
...
»

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

Anybus Communicator ABC4021

Brand: HMS Networks Pages: 60

Brand: ICP DAS USA Pages: 62

Brand: Airvana Pages: 90

Brand: C&H Technologies Pages: 50

RuggedSwitch RS500

Brand: RuggedCom Pages: 16

Brand: Premio Pages: 2

Brand: Tripp Lite Pages: 2

Brand: TDT Pages: 8

Brand: Xaptum Pages: 24

Brand: TCL Pages: 22

Brand: Magnescale Pages: 73

Brand: Asus Pages: 11

Brand: Asus Pages: 22

Brand: Asus Pages: 2

Brand: Asus Pages: 2

RT-N13U - Wireless Router

Brand: Asus Pages: 2

Brand: Asus Pages: 53

Brand: Asus Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands