manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 156 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 156

Service Management Tasks

Page 156

7750 SR OS Interface Configuration Guide

Service Management Tasks

This section discusses basic procedures of the following service management tasks:

•

Modifying or Deleting an MDA on page 156

•

Modifying a Card Type on page 157

•

Deleting a Card on page 157

•

Deleting Port Parameters on page 157

Modifying or Deleting an MDA

To change an MDA type already provisioned for a specific slot/card, first you must shut down the 
slot/MDA/port configuration and then delete the MDA from the configuration. 

Use the following CLI syntax to modify an MDA:

CLI Syntax:

config> port 

port-id

shutdown

CLI Syntax:

config> card 

slot-number

shutdown

[no] mda 

mda-number

[no] mda-type 

mda-type

[no] hi-bw-mcast-src [alarm] [group 

group-id

]

shutdown

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments