Alcatel-Lucent 1643 AM Operation Manual Download | Manualshive

Page: 208 / 386

background image

STM-4 MS Alarm indication signal received

...................................................................................................................................................................................................................................

Alarm identifier

MS4cAIS

Information

When the Alarm Indication Signal (AIS) is received, then:

•

The STM-4 MS contains all 1s (alarm indication signal).

•

The upstream equipment has detected a defect and responded to it.

Alarm category

Transmission

ASAP

sdhMS

Alarm severity
(default setting)

Information

Reporting state
(default setting)

Reported

Local indications

In the upstream direction, “Multiplex Section - Remote Defect Indicator”
(MS-RDI) is inserted.

Cause

In the upstream equipment a defect has been detected, and as a consequent
action, AIS has been inserted in the downstream direction.

Actions

Locally no actions need to be taken. Analyze the alarm state of the upstream
equipment and take appropriate measures.

Note(s)

There are no actions needed concerning the indicated network element; alarm
indication signal is only reported for information.

Alarm messages

...................................................................................................................................................................................................................................

1-188

Alcatel-Lucent - Proprietary

See notice on first page

365-312-803R7.2

Issue 4, May 2007

«
...
206
207
208
209
210
...
»

Summary of Contents for 1643 AM



































































































































































































































































































































































































Reviews:

No comments

Related manuals for 1643 AM

Brand: Tektronix Pages: 32

Brand: Nexperia Pages: 32

Brand: IDEAL INDUSTRIES Pages: 25

Brand: Keysight Pages: 9

Brand: TECPEL Pages: 40

Brand: Elma Pages: 32

Brand: Perfomance Tool Pages: 16

Brand: GE Security Pages: 9

Brand: Oakton Pages: 76

Brand: Mastech Pages: 10

Brand: Pantron Pages: 12

IMX-A840 Series

Brand: Pantron Pages: 16

Brand: National Instruments Pages: 128

Brand: Dawson Tools Pages: 10

Brand: Benning Pages: 184

Brand: Quark-Elec Pages: 2

Brand: Wetekom Pages: 43

Brand: Tektronix Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands