Albatron SIL 3112 User Manual Download Page 7 | Manualshive

Page: 7 / 36

Albatron SIL 3112 User Manual Download Page 7

SATARaid Controller Manual

4

Creating/Deleting RAID Sets

(BIOS RAID Configuration Utility)

Creating and deleting RAID sets are done using the BIOS RAID Configuration Utility. During
bootup, the following message will appear, pausing for a few moments allowing the user to
enter the RAID utility.

“Press <CRTL-S> or F4 to enter RAID utility”

The BIOS RAID Configuration Utility screen will appear as shown below:

The top-left portion of the screen lists the basic functions. The bottom-left portion of the screen
lists the SATA drives currently installed on the system. The top-right portion of the screen
displays instructions and comments for the user. The bottom-right portion lists the command
keys.

Creating RAID Sets

This mainboard supports only two SATARaid drives and so configuring RAID Sets is a
relatively simple procedure.

1. From the BIOS RAID Configuration Utility select “Create RAID Set.”

2. Choose either a “Striped” or “Mirrored” RAID Set. (note that a “Striped Set” and a

“Mirrored Set” cannot be configured concurrently).

RAID Configuration Utility – Silicon Image Inc. Copyright © 2003

▲▼

Select

Menu

ESC Previous

Menu

Enter

Select

Ctrl-E Exit

*

0 PM ST3120026AS 114473MB

1

SM ST3120023AS 114473MB

Create RAID set

Delete RAID set

Rebuild Mirrored set

Resolve Conflicts

Low Level Format

Press “Enter” to create RAID

set

Important Note

Before you configure any SATA hard drives into your system, backup any
important data as a safety precaution.

«
...
5
6
7
8
9
...
»

Summary of Contents for SIL 3112





































Reviews:

No comments