Albalá Ingenieros AGW3000C01 Manual Download Page 16 | Manualshive

Page: 16 / 48

background image

Albalá Ingenieros | Manual

AGW3000C01

3.6.1. Electrical DVB-ASI video connections

All DVB-ASI digital video electrical connections are BNC type. Below are several
recommendations to consider when wiring electrical signals.

BNC connectors used on cables must be suitable for the high frequencies of DVB-ASI
digital video signals: it is strongly recommended to use high quality connectors from
well known manufacturers.

All coaxial cable used must be Belden 8281 or similar. This type provides the greatest
lengths because it is used to calculate the equalizers in the AGW3000C01. Cables
carrying signal between the module and the devices should use single piece
construction, avoiding spliced sections with double BNC female or barrel connectors.
If it is necessary to split the cable into two sections the same type of wire should be
used in both sections.

The use of analog video coaxial cables (RG-59 type or similar) is not recommended for
digital video except for very short distances.

16

«
...
14
15
16
17
18
...
»

Summary of Contents for AGW3000C01

















































Reviews:

No comments

Related manuals for AGW3000C01

Brand: Snell & Wilcox Pages: 51

Brand: Kostal Pages: 12

SUNNY BOY 3000-US

Brand: SMA Pages: 36

Brand: Tektronix Pages: 11

Brand: Microsens Pages: 2

Brand: IAdea Pages: 33

SUNNY TRIPOWER 20000TL High Efficiency

Brand: SMA Pages: 46

Brand: Tecsun Pages: 2

Gold Link Dac III

Brand: MSB Technology Pages: 12

Brand: SolaX Power Pages: 60

JNTHBCBA0001BEAU

Brand: TECO Pages: 98

Brand: Wavtech Pages: 12

Brand: Lindy Pages: 2

Brand: Transition Networks Pages: 8

Brand: Clayton Power Pages: 12

Brand: Hitachi Pages: 38

SJ300-EL Series

Brand: Hitachi Pages: 52

Brand: Hitachi Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands