Alba EX116AX, Instruction Manual

Page: 7 / 10

- THE CD IS NOW READY TO BE PLAYED.
- TO REMOVE A DISC, FOLLOW THE SAME PROCEDURE AS DESCRIBED ABOVE,EXCEPT TO REMOVE THE CD
INSTEAD OF INSERTING IT INTO THE COMPARTMENT, BY PLACING ONE FINGER AT THE MIDDLE OF DISC
(CENTER SPINDLE) & THE OTHER AT THE EDGE OF THE DISC & GENTLY PULLING UPWARDS.
- IMPORTANT : ALWAYS HOLD A CD BY ITS EDGES. AVOID GETTING ANY FINGER PRINTS, SMUDGES OR DIRT
ONTO THE SURFACE OF A DISC. IN CASE THIS HAPPENS, USE A SPECIAL CD-CLEANING CLOTH OR CLEANING
KIT TO REMOVE THE DIRT OR SMUDGES.
ALBA User Manual
- 5 -
- PRESS THE SEEK/SCAN SWITCHES OR TO SELECT THE TRACK (SONG) NUMBER YOU WISH TO
BE STORED IN THE FIRST MEMORY (PROGRAM) POSITION, AND PRESS (PROGRAM) TO CONFIRM
YOUR SELECTION.
- WHEN YOU PRESS THE DISPLAY WILL ADVANCE TO THE NEXT MEMORY POSITION (eg. “02”).
- REPEAT THE PREVIOUS 2 STEPS, EACH TIME SELECTING ANY TRACK NUMBER OF YOUR CHOICE TO BE STORED
IN THE SUCCESSIVE MEMORY (PROGRAM) POSITIONS.
- AFTER EACH TRACK NUMBER, REMEMBER TO PRESS THE PROGRAM SWITCH .
- AFTER A MAXIMUM OF 20 SONGS (OR LESS) HAVE BEEN SELECTED AS DESCRIBEDABOVE, PRESS THE
SWITCH.
- THE DISPLAY WILL NOW SHOW THE EXACT SONG SEQUENCE IN MEMORY BY DISPLAYING ALL THE SONG
NUMBERS RAPIDLY.
- ALSO, THE “PROG” WILL REMAIN “ON” TO INDICATE THAT YOU HAVE SAVED APROGRAM-MEMORY
(SEQUENCE).
- PRESSING PLAY WILL NOW PLAY BACK THE “SAVED SEQUENCE” IN THE PROGRAM MEMORY.
- TO CLEAR (CANCEL) THE ENTIRE PROGRAM WHICH IS STORED IN THE MEMORY, SIMPLY PRESS “STOP”
TWICE, OR SWITCH “OFF” THE SET.
NORMAL CD OPERATION
IMPORTANT:
MAKE SURE THERE IS NOTHING PLUGGED INTO THE AUX JACK.
- SLIDE THE FUNCTION SWITCH TO “CD(AUX)”.
- THE CD WILL SPIN MOMENTARILY AND THEN THE DISPLAY WILL SHOW THE TOTAL NUMBER OF T
RACKS (SONGS) OF
T HE DISC.
- PRESS THE PLAY/PAUSE BUTTON . THE DISK WILL START SPINNING & THE FIRST SONG (TRACK) WILL START
PLAYING. THE DISPLAY WILL INDICATE THE CURRENT TRACK NO. (“01” IF IT IS THE FIRST TRACK).
- AT ANYTIME DURING PLAYBACK, PRESS THE “PLAY/PAUSE” BUTTON TO PAUSE OPERATION OF THE UNIT.
PRESS PLAY/PAUSE BUTTON TO RESUME OPERATION AT THE SAME TRACK & POSITION.
- AT ANYTIME DURING PLAYBACK, PRESS THE “STOP” BUTTON TO STOP OPERATION OF THE SET. THIS WILL RESET
THE CD-PLAYER TO THE FIRST TRACK (IF YOU PRESS PLAY AFTER STOP, THE FIRST TRACK WILL ALWAYS
START PLAYING).
- AT ANYTIME DURING PLAYBACK, “PRESS AND RELEASE” THE SEEK/SCAN BUTTONS : OR TO SKIP
BACKWARDS OR FORWARDS BY ONE TRACK, AS DESIRED.
- AT ANYTIME DURING PLAYBACK, “PRESS AND HOLD” THE SEEK/SCAN BUTTONS : OR TO
FAST-REVERSE (REVIEW) OR FAST-FORWARD (CUE) THE SPECIFIC TRACK, WHICH IS CURRENTLY PLAYING.
- AT ANYTIME DURING PLAYBACK, PRESS THE “CD REPEAT BUTTON” AS FOLLOWS:
- INSERT A CD AS DESCRIBED.
PRESS ONCE = DISPLAY WILL SHOW “REPEAT 1”, TO REPEAT THE
CURRENT TRACK
PRESS TWICE = DISPLAY WILL SHOW “REPEAT ALL” ,TO REPEAT
ALL TRACKS (FULL CD)
PROGRAMMING THE CD-PLAYER
- THE CD PLAYER CAN BE PROGRAMMED TO PLAY ANY SEQUENCE OF UP TO 20 TRACKS, AS DESIRED.
- ALWAYS PRESS THE STOP KEY BEFORE STARTING THE PROGRAMMING.
- PRESS THE PROGRAM SWITCH ,THE DISPLAY WILL SHOW “PROG” AND THE “01” WILL FLASH,
TO INDICATE THAT THE SET IS NOW IN “MEMORY PROGRAMMING MODE”, AT THE FIRST MEMORY POSITION.
NEXT BACK
NEXT BACK
PROG.
PROG.
PROG.
NEXT BACK
PROG.
PROG.
PROG.