27
Programming Functions (cont'd)
;
6
7
;
[ _ _ ]
:
(Event
Number)
67. Add System Features
4
Relay Features
(For locks equipped with an internal relay)
Use Function 67 to program
one or more
lock events and the relay will energize when the programmed event(s) listed
below occurs. For example, program
;
6
7
;
3
:
and when an attempted entry fails (such as a
User who enters an incorrect or un-programmed User Code), the relay will energize for 2 seconds.
Note:
For more infor-
mation about the
Remote Input
, see page 14 (
WIRING
,
Remote Input
) and page 26 (Function 65).
1.
Remote Input switch closed and Function 65
Remote Input
enabled.
Because the Remote Input is enabled by facto-
ry default, the relay will energize when the Remote Input switch is closed.
2.
Remote Input switch closed and Function 64
Remote Input
disabled.
If the Remote Input is disabled with Function
64, the relay will energize when the Remote Input Switch is closed.
3.
Failed attempted entry.
Relay energizes for 2 seconds when an attempted User Code entry (or proximity card)
fails.
4.
Disabled User or Group.
Relay energizes for 2 seconds when a disabled User or disabled Group member enters a
User Code (or proximity card).
5.
Follow Access Granted.
When a valid User Code is entered into the keypad and the lock unlocks, the relay energiz-
es for 2 seconds. Compare with Event 31.
6.
Group 1 User Code.
Relay energizes for 2 seconds when a scheduled Group 1 User Code (or proximity card) is entered.
See Function 90, page 31.
7.
Scheduled Lock Event.
Relay energizes for 2 seconds when lock is locked by a Schedule.
8.
Scheduled Unlock Event.
Relay energizes for 2 seconds when lock is unlocked by a schedule
9.
Lock Out.
Relay energizes for 2 seconds when a Lock Out occurs (i.e. number of attempts is exceeded, see Func-
tion 60).
10.
Ambush.
Relay energizes for 2 seconds when Ambush is tripped. See Function 66, page 26.
11.
First Key Press.
Relay energizes for 2 seconds at the first key press of any sequence.
12.
Activate Relay On Door Ajar.
If the door is held open for longer than the allowed Door Ajar Trip Time
(programmed at Function 68) the relay will engage for 2 seconds. See "Door Ajar" in glossary.
14.
Activate Relay On Forced Door.
If the Door Position Contacts detect the door was opened without first a
valid credential unlocking the lock, or the door was opened without first the inside lever turned (to activate the Lever
Monitor Switch), the relay will engage for 2 seconds. See "Forced Door" in glossary.
31.
Follow Access Granted--No Time Limit.**
When a valid User Code is entered into the keypad and the lock unlocks,
the relay energizes for the
same amount of time as the programmed Pass Time
. (The Pass Time is the length of time the
lock stays unlocked after a valid User Code is entered. See functions 52-54). Use this feature for remote monitoring or
other activation as this feature works independently of all other relay options. Programming this feature will supersede all
other programmed relay features. Subsequent relay feature programming will not take effect while this feature is active. Be-
fore programming any other relay features, press
;
6
8
;
0
0
0
:
to delete this feature.
System Options
24. One Time Access for Group 3 Users***
25. Disable Sounder
26. 5 sec. Delayed Entry *
27. 15 sec. Delayed Entry *
28. 45 sec. Delayed Entry *
Remote Input Functions
29.
Toggle Passage Mode.
Remote Input toggles Passage Mode.
30.
Forced Unlock Follows Remote Input.
** When Remote Input switch is closed, regardless of the current state of
the lock, the lock unlocks for the duration of the Remote Input switch closure.
32.
Remote Input Disables Unit.
**
Regardless of the current state, that state will remain unchanged (and keypad will
be disabled) for the duration of Remote Input switch closure.
34.
Forced Lock Follows Remote Input
** When Remote Input switch is closed, regardless of the current state
of the lock, the lock will lock for the duration of the Remote Input switch closure.
Enable Emergency Commands
†
38.
Lock responds to "Global" Emergency Commands.
(Default = OFF, thus default = Lock responds to " Local"
Emergency Commands only). Allows lock to respond to Emergency Lockdown requests initiated by Networx server
running DL-Windows or another lock (as opposed to directly from a Wireless Remote Release).
† †
