AL-DTM OVERVIEW
Data Transfer Modules allow the transfer of lock pro-
grams and other data between DL-Windows software
and Alarm Lock locking devices. The improved DTM-III
allows for more locks to be stored per account, both
within DL-Windows and within the DTM-III itself. These
instructions will allow you to configure for the improved
DTM-III operation.
DTM's that start up with the message "
Alarm Lock
DTM-II-III, V1.XX
" will operate in both the DTM-II
and DTM-III modes. Units configured to operate in
DTM-III mode will display "DTM-III" when prompting us-
ers to enter lock mode. The DTM-III mode is required
for DL-Windows 3.5.3 operation, and likewise DL-
Windows 3.5.3 is required for use with DTM-III mode.
Note:
If you are unsure about your version of DL-
Windows, version numbers can be found in the DL-
Windows
Help
,
About
screen. Products shipped as
DTM-III have been factory configured for DTM-III mode
ON
and Door Select Mode
OFF
.
AL-DTM-III SETUP
Configure the internal DTM software for DTM-III op-
eration:
1. From the
Power On
or
PC Comm.
mode, press and
HOLD
both the left and green buttons on the DTM.
After several messages appear,
release the buttons
when the display reads:
2. When the display reads "
CONFIG. LANGUAGE
", the
DTM has entered its configuration and self-test
mode.
3. Press and release the green button once and the
display will read "
CONFIG FOR DTM-III MODE
".
4. Press and
HOLD
the green button until the DTM
beeps--release the button and the display reads:
The top line of the display indicates that DTM-III
mode is currently off; the bottom line corresponds to
the three buttons on the DTM.
Therefore, to activate DTM-III operation, press the
left button. The top line of the display will now read:
(
Note:
If using DL-Windows versions earlier than
3.5.3, you must press the center button to keep
DTM-III operation off--thus retaining DTM-II opera-
tion).
5. Press the green button to exit this sequence. "
TASK
ENDING!
" will appear briefly. The DTM will proceed
directly to "Door Selection Mode" as described in the
next section.
ENABLE DOOR SELECTION MODE
Door Selection Mode is only needed if performing
initial lock programming using DL-Windows 3.5.3.
See the DL-Windows User's Guide OI237 for more
information about Door Selection Mode.
1. When configuring to allow Door Select Mode, the
display will switch between the following:
2
.
Press and
HOLD
the green button until the DTM
beeps--release the button and the DTM will display:
The top line of the display indicates that Door Select
mode is currently off; the bottom line corresponds to
the three buttons on the DTM.
Therefore, if using DL-Windows Version 3.5.3 or
later and you wish to use the AL-DTM-III to provide
initial
programming to
existing
locks, press the left
button (selecting "ON") to enable DOOR SELECT
Mode. The top line of the display will now read:
(
Note:
You may press the center button to keep
Door Select mode off, provided all system locks are
already enrolled in the DL-Windows 3.5.3 program.
See the DL-Windows User Guide for details regard-
ing Door Select mode).
3. Press and release the green button (again and
again) until the DTM Displays:
4. Press and hold the green button until the DTM
Beeps. The DTM will perform a brief power control
test (
TEST RUNNING!
) and then shut down within 5
seconds.
Release the
buttons when
displayed
ENTERING
CONFIG/TEST MODE
DTM-III MODE=OFF
ON OFF EXIT
DTM-III MODE=ON
ON OFF EXIT
CONFIG. DOOR
SELECT MODE
Hold Button=Run,
Press=Next Test
DOOR SELECT= OFF
ON OFF EXIT
Sleep Then
Power Down.
DOOR SELECT= ON
ON OFF EXIT