1
OVERVIEW
The
RR-RECEIVER
is a wireless general-purpose remote
control receiver that provides remote unlocking to an Alarm
Lock locking device,
or for any other application requiring a ra-
dio-controlled solid state relay closure
.
The RR-RECEIVER is factory supplied with Alarm Lock com-
patible battery connector plugs, simplifying installation within
Alarm Lock cylindrical locking devices for wireless "remote re-
lease". The RR-RECEIVER can be used with a standard Alarm
Lock battery pack or by simply cutting the power battery con-
nector and using your own power supply (see
SPECIFICA-
TIONS
for current consumption and power requirements).
RR-RECEIVER features include:
Can be installed inside the lock housing to provide a
"remote release" (remote unlock) function with legacy Alarm
Lock locking devices (models DL2700, DL2800 or T3 non-
Networx models without an integral radio
Built-in battery connectors for quick installation
inside Alarm Lock T2 or T3 locking devices
Programmable "
Relay Closure Duration
",
"
Relay 'Hold Off' Time
" and "
Relay Toggle
Mode
" for advanced applications
Compatible with both the
RR-1BUTTON
wire-
less remote (see WI1999) and the
RR-4BKEYFOB
4-
button pocket-size remote (see WI2004). Use a
RR-
4BKEYFOB
if you want a single " keyfob remote" to ac-
tivate up to 4 separate RR-RECEIVER's (for example, each
button opens a separate door)
Up to fifty (50) individual remote buttons can be
"paired" (connected) to one RR-RECEIVER
Can be used to drive high loads such as door
strikes or magnetic locks by wiring to an auxilia-
ry high current relay (see
Specifications
and
Wiring Diagram
for more information)
Years of operation with a standard Alarm Lock
battery pack (see
Specifications
below for cur-
rent consumption and power requirements)
Relay programming and remote button pairings are main-
tained even when power is removed
For mortise locks, use the RR-MORTISE kit
Note:
In this manual, " remote button" is used to describe
the single button on the RR-1BUTTON (see WI1999) or any
one of the four buttons on the RR-4BKEYFOB (see WI2004).
SPECIFICATIONS
Power Requirements
: ......... 5-12VDC or use AL battery pack
Solid State Relay Contact Current
: ............. 30mA maximum
Current Consumption
: ..... 50 microamperes (µA) idle current
OPERATION
When a paired remote button is pressed, its paired RR-
RECEIVER relay will typically close within 2 seconds of the but-
ton press, and will remain closed for its programmed "
Relay
Closure Duration
" (2 seconds by default, programmable
from 1-250 seconds).
After the "
Relay Closure Duration
" ends and the relay opens, an
optional
Relay "Hold Off" Time
can be added during which time
the RR-RECEIVER will ignore all paired remote button presses
(
Relay "Hold Off" Time
is 0 seconds by default, program-
mable from 0-250 seconds). After the
Relay "Hold Off" Time
ends, the RR-RECEIVER is then ready to respond to the next
wireless remote button press. This
Relay "Hold Off" Time
might
be used for mechanical locking devices that require a minimum
time to complete their operation, such as an entry gate swinging
mechanism or mortise locks that require extra time to complete
their mechanical operations (we recommend a minimum of 3
seconds "Hold Off" time be programmed when the RR-
RECEIVER
is used with Alarm Lock Exit Trim and Mortise lock-
ing devices). The columns in the table below (from left to right)
summarize these RR-RECEIVER operations:
A separate programmable relay option is "
Relay Toggle Mode
"
where each press of a paired remote button causes the relay to
alternate back and forth between open and closed states like a
toggle switch. See "
RELAY TOGGLE MODE
" for details.
Note:
If "
Relay Toggle Mode
" is programmed, we recom-
mend powering the RR-RECEIVER
with a DC power supply, as
the voltage drain due to extended relay close durations will de-
crease battery life. See
SPECIFICATIONS
.
CAPACITY
Up to fifty (50) individual remote buttons can be "paired" to
one
RR-RECEIVER. However, a remote button can only be paired
with
one
RR-RECEIVER at a time.
If a paired remote button is
later paired with a second RR-RECEIVER, the first pairing will
be erased.
GETTING STARTED
First power the RR-RECEIVER, then perform the "Pairing Pro-
cedure" and "Relay Operational Programming".
For installations inside Alarm Lock housings:
Jump to
the section "
INSTALLATION INSIDE AN ALARM LOCK
DEVICE HOUSING
". You can perform the "Pairing Proce-
dure" and "Relay Operational Programming" with the RR-
© ALARM LOCK 2016
WI2012A 02/16
RR-RECEIVER
Wireless General Purpose Remote Control Receiver
INSTALLATION AND PROGRAMMING INSTRUCTIONS
RR-4BKEYFOB
RR-1BUTTON
Remote
Button
Press
RR-RECEIVER
"Relay Closure
Duration"
RR-RECEIVER "Relay
'Hold Off' Time
RR-RECEIVER "Relay
'Hold Off' Time Ends
0.5-2 sec.
delay
before
relay
closes
Default is 2
seconds;
programmable
between 1-250
seconds
Relay opens and ignores
all paired remote button
presses. Default time is
zero seconds;
programmable between
0-250 seconds
The RR-RECEIVER is
ready to respond to the
next wireless remote
button press
S U M M A R Y O F R R - R E C E I V E R R E L A Y
O P E R A T I O N S O V E R T I M E
345 Bayview Avenue
Amityville, New York 11701
For Sales and Repairs 1-800-ALA-LOCK
For Technical Service 1-800-645-9440
or visit us at
http://tech.napcosecurity.com/
(Note: Technical Service is for security professionals only)
Publicly traded on NASDAQ Symbol: NSSC
