2
6. Test to ensure correct operation:
Testing the Wireless Remote is
required
to synchronize the
Wireless Remote with the locking device. Furthermore, the
first time you perform the test below, the locking device may
not always open on the first try. DO NOT BE CON-
CERNED, this is
normal
during this testing process. Test
as follows:
a. At the keypad, exit Program Mode by pressing and
holding any keypad button.
b. Press and release the paired Wireless Remote button.
c. The LED lights red...
d. ...within two seconds, the LED turns off...the locking de-
vice should open.
If not, do not be concerned, this is
normal
. Wait a few seconds and start again at step b
above. When the locking device unlocks and relocks,
the testing process ends and "normal" Networx system
operation resumes.
Note:
During normal operation, the locking device is
designed to always open on the first button press (no
need to "press and hold"; one press is sufficient).
CLEARING THE FOB
This procedure removes the pairings of all Wireless Remote
buttons to all locking devices (essentially "un-pairing" the fob of
all paired data and restoring the fob to its default settings).
Note:
This procedure is not
required
to allow a previously
paired button to be paired with a new locking device; simply pair
the button with the new locking device as per the "
PAIRING
PROCEDURE
" on page 1 and the first pairing will be erased.
But if you wish to remove the pairings of all buttons, proceed as
follows:
1. Remove the key ring
from the Wireless Remote case.
2. Carefully insert the edge of a small coin
in the notch
located in the bottom right corner of the Wireless Remote
(near the key ring loop). Open the case by gently twisting
the coin. Lift off the top cover.
3. Carefully remove the circuit board
.
4. On the bottom side of the circuit board
, push the bat-
tery cell out of its metal holder with a sharp pencil. The
cell will slide out of its holder as shown in the image be-
low.
Note the orientation of the cell polarity, with its posi-
tive side up, before fully
removing the cell.
5.
Press and hold any
Wireless Remote but-
ton on the circuit
board
. Keep holding
the button and replace
the battery
positive (+)
side up
, by sliding the
battery into its metal
bracket.
Continue
holding the button
.
6. While holding
, wait until the LED rapidly toggles between
red and green ("
red-green-red-green
" continuously),
then release the button. All buttons will be "un-paired",
and will be available for future pairings.
7. Reassemble the case
by first placing the circuit board,
battery side down, into the Wireless Remote base.
Place the top of the Wireless Remote (with its rubber
button/gasket in place) on the Wireless Remote base
and press to snap the two Wireless Remote pieces to-
gether.
8. Test the Wireless Remote
operation.
C L E AR A L O C K I N G D E V I C E
Up to ten (10) Wireless Remote buttons (on multiple keyfobs)
can be simultaneously paired with one individual Networx lock-
ing device. To remove all paired Wireless Remote buttons from
a single locking device, use Function 64, as follows:
1. At the locking device keypad
, enter Program Mode
(press the Master Code and press
;
).
2. Press the following
:
;
6
4
:
Note:
Function 64 will disable all hardwired remote re-
lease ("Remote Input") switches, if present. In addition, if
a Wireless Remote is misplaced or stolen, it will be nec-
essary to remove ALL Wireless Remote buttons from the
locking device to ensure system security.
3. Exit Program Mode
(press and hold any button until a
series of beeps is heard).
L O W B AT T E R Y I N D I C AT I O N
During normal operation, when a button on the Wireless Re-
mote is pressed and its battery is weak, the LED on the Wire-
less Remote will flash red-green repeatedly for several seconds.
Always replace a weak battery as soon as possible (see below
"
BATTERY REPLACEMENT
" procedure).
B AT T E R Y R E P L AC E M E N T
Use a 3V Lithium type CR2032 or Duracell DL2032 only; use of
another battery may present a risk of fire or explosion.
Be care-
ful NOT to press any buttons during this procedure
.
1. Remove the key ring
from the Wireless Remote case.
2. Carefully insert the edge of a small coin
in the notch
located in the bottom right corner of the Wireless Re-
mote (near the key ring loop). Open the case by gently
twisting the coin. Lift off the top cover.
3. With the bottom half of the Wireless Remote facing
upwards
, carefully remove the circuit board.
4. On the bottom side of the circuit board
, push the bat-
tery out of its metal holder with a sharp pencil. The bat-
tery will slide out of its holder as shown in the image at
left.
Note the orientation of the battery polarity, with its
positive side up, before fully removing the battery.
5. Replace with a new battery
,
positive (+) side up
, by
sliding the battery into its metal bracket.
Be certain of
battery polarity before installation
.
6. Reassemble the case
by first placing the circuit board,
battery side down, into the Wireless Remote base.
Place the top of the Wireless Remote (with its rubber
button/gasket in place) on the Wireless Remote base
and press to snap the two Wireless Remote pieces to-
gether.
7. Test the Wireless Remote
operation. Follow the steps
detailed on page 1 in the "
PAIRING PROCEDURE
" step
6.
R E P L AC I N G A L O C K I N G D E V I C E
If the paired locking device is physically replaced with a new
locking device, the "
PAIRING PROCEDURE
" must be repeated
with each desired Wireless Remote button.
Battery Replacement
Insert pencil and
push cell out of
holder as shown
©
N
APC
O
06
022
2032
