Alarm.Com Concord 4 Dual-Path LTE Installation Manual Download Page 6

 

 

Copyright © 2015 Alarm.com

 

|

 

www.alarm.com 

|

 v1_2

 

 

Concord 4 LTE Module

 

|

 

Installation Guide 

| 

ADC-87-008700-112     

Regulatory Information                                                     

 

                                    

Table 7: Regulatory Listings 

Listings 

FCC ID: YL6-143470L  
IC: 9111A-143470L 
Model Number: ADC-470L 

 

Changes or modifications not expressly approved by Alarm.com can void 
the user’s authority to operate the equipment.  
 
This equipment has been tested and found to comply with the limits for 
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to 
radio communications. However, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged 
to try to correct the interference by one or more of the following 
measures:  
 

 

Reorient or relocate the receiving antenna.  

 

Increase the separation between the equipment and receiver.  

 

Connect the equipment into an outlet on a circuit different form 
that which the receiver is connected  

 

Consult the dealer or an experienced radio/TV technician for help.  
 

Operation is subject to the following two conditions:  
(1) This device may not cause interference  
(2) This device must accept any interference, including interference that 
may cause undesired operation of the device  
This equipment complies with the FCC RF radiation exposure limits set 
forth for an uncontrolled environment. This equipment should be 
installed and operated with a minimum distance of 20 centimeters 
between the radiator and your body. 

Summary of Contents for Concord 4 Dual-Path LTE







Reviews: