background image

10

10

 

 Notices

 

 Federal Communication Commission  
interference statement

 
 

 This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference to 
radio communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following 
measures:

 
• 

Reorient or relocate the receiving antenna.

• 

 Increase the separation between the equipment and receiver.

• 

 Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected.

 
• 

 Consult the dealer or an experienced radio/TV technician for help. Changes or 
modifications not expressly approved by the party responsible for compliance could void 
the user’s authority to operate this equipment.

 

ISED statement

 

 This device contains licence-exempt transmitters(s)/receiver(s) that comply with 
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). 
Operation is subject to the following two conditions:

 
1. 

This device may not cause interference. 

2. 

 This device must accept any interference, including interference that may 
cause undesired operation of the device.

 

 L’émetteur/récepteur exempt de licence contenu dans le présent appareil est  
conforme aux CNR d’Innovation, Sciences et Développement économique Canada 
applicables aux appareils radio exempts de licence. L’exploitation est autorisée  
aux deux conditions suivantes:

1. 

L’appareil ne doit pas produire de brouillage;

2. 

L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage 

 

est susceptible d’en compromettre le fonctionnement.

 

 This radio transmitter [IC: 4491A-V723] has been approved by Innovation, Science and 
Economic Development Canada to operate with the antenna types listed below, with 
the maximum permissible gain indicated. Antenna types not included in this list that 
have a gain greater than the maximum gain indicated for any type listed are strictly 
prohibited for use with this device.

11

No.

Antenna Type

Model Number

Antenna Gain(dBi)

Remark

1

Dipole

3010001121L7

5.1

2.4GHz

5.6

5GHz

2

Dipole

3010001122L7

3.5

2.4GHz

5.5

5GHz

Summary of Contents for ADC-V724
















Reviews: