manualshive.com logo in svg

Alamo Bush Hog HDE-4 Series, Operator'S Manual

Share
Download
Alamo Bush Hog HDE-4 Series Operator'S Manual Download Page 11

PUMP BELT INSTALLATION .....................................................................................................6-9
CUTTING BLADE MAINTENANCE ...........................................................................................6-9

Blade Removal...........................................................................................................................................................6-9
Inspect Blades ...........................................................................................................................................................6-9
Sharpening Blades...................................................................................................................................................6-10
Installing Blades.......................................................................................................................................................6-10

ADJUSTING the MOWER DECK.............................................................................................6-10

Leveling the Deck ....................................................................................................................................................6-10

TRANSAXLE MAINTENANCE .................................................................................................6-11

Fluid and Filter Change Procedure ..........................................................................................................................6-11
Purging Procedures .................................................................................................................................................6-12

CONSOLE MAINTENANCE ...........................................................................................6-13- 6-15

General Care ...........................................................................................................................................................6-14
Bypass or Failed Safety Interlock Switch Detection.................................................................................................6-14
Service Alerts ...........................................................................................................................................................6-14
Alarms......................................................................................................................................................................6-14
Console Diagnostic Codes.......................................................................................................................................6-15
Spark Arrestor Maintenance ....................................................................................................................................6-16

STORAGE (SECTION 7)

WINTER STORAGE ...................................................................................................................7-1

Preparing the Machine for Storage ............................................................................................................................7-1
New Season Preparation ...........................................................................................................................................7-1

TROUBLE SHOOTING (SECTION 8) .....................................................................8-1

TECHNICAL DATA (SECTION 9)

MAIN WIRING HARNESS .........................................................................................................................................9-1
MAIN WIRING HARNESS SCHEMATIC ...................................................................................................................9-2
ENGINE ADAPTOR HARNESS for KAWASAKI ENGINES.......................................................................................9-3
ENGINE ADAPTOR HARNESS for KOHLER ENGINES ..........................................................................................9-4
TORQUE SPECIFICATIONS .....................................................................................................................................9-5
SERVICE and MAINTENANCE RECORDS ..............................................................................................................9-6

Summary of Contents for Bush Hog HDE-4 Series







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands