background image

4.3.4 Show firmware version

Firmware version consists of three digits (x.y.z). 

 check which firmware version the system is running 

follow the next sequence:

Long press        button to enter menu. The LED will turn yellow, the color of the main menu. 

Press         four (4) times and then press       . 
The number of red LED blinks and beeps from the speaker signalizes the first digit;

white LED blinks and beeps from the speaker signalizes the second digit;

 of blue LED blinks and beeps from the speaker signalizes the third digit.

Restore factory default settings

Did you forget which features you programmed into your system? Use this simple programming sequence 
to restore factory default settings:

Long press        button to enter menu. The LED will turn yellow, the color of the main menu. 

Press         five (5) times and then press       . 
The system will restore settings and restart.

Automatic sensor check

While  restoring  factory  default  settings  the  unit  will  count  and  memorize  the  number  of  sensors 
connected to the system as well as their positions. On each subsequent power-up during the self-test 
process the unit will check if all memorized sensors are present and operational. If one or more are 
disconnected or not operational you will be warned by a constant red LED light and short beeps 
during first 5 seconds of operation. 

NOTE: In order to memorize any change initiate this setting after installation of every new sensor.

To

 

4.3.5 

 and memorize number of installed sensors

The number of 
The number

4.3.3 LED Dark mode (DEFAULT: OFF)

To prevent the green light from flashing every second during operation, you can activate the LED Dark 
mode. The green light will stop flashing 10 seconds after the power-up if this mode is activated. 

Long press        button to enter menu. The LED will turn yellow, the color of the main menu. 

Press        three (3) times and then press       . 

Reprogramming will be signalled by a green blinking LED and three beeps from the speaker if this 

mode is turned ON, or a red LED light with long beep if this mode is turned OFF. 

11          AL PRIORITY User Guide

www.alpriority.com

Summary of Contents for car parking sensor


















Reviews: