AL-KO LSV 550/6, Manual

Page: 34 / 96

GB
34 LSV 550/6 | LSV 560/8
Assembly
3. Push wheel (06/5) and washer (06/6) onto
the wheel shaft.
4. Insert cotter pin:
■
Push cotter pin (06/7) through the hole in
the wheel shaft.
■
Bend open the legs of the cotter pin in
opposite directions and spread.
5. Push on wheel cap (06/8).
5.1.2 Attach splitting table [LSV 550/6] (07 –
09)
1. Unscrew star handles (07/1) out of lateral
brackets (07/2) until the splitting table can be
pushed in.
2. Fold up (08/a) lateral rests (08/1) of splitting
table (08/2) until they engage and form a lev-
el surface with the splitting table.
3. Push (09/a) splitting table (09/1) into lateral
brackets (09/2) until hooks (09/3) of the split-
ting table engage.
4. Screw star handles (09/4) securely into the
lateral brackets until the splitting table is
fixed.
Proceed analogously in reverse order to remove
the splitting table.
5.1.3 Attach operating arms [LSV 550/6] (10
– 13)
Perform the steps described here for both operat-
ing arms:
1. Insert M10 x 25 screw (11/1) with small
washer (11/2) through the hole in operating
arm (11/3).
2. Place operating arm on transverse plate
(12/4). Carry out simultaneously:
■
Insert lever (12/5) of the hydraulic pump
controller into the recess in the operating
arm.
Note: Pay particular attention that the le-
ver is inserted correctly!
■
Align the holes in operating arm and
transverse plate.
■
Push screw (11/1) with small washer
(11/2) through the holes.
3. Insert large washer (12/6) between operating
arm and transverse plate. Carry out simulta-
neously:
■
Raise operating arm slightly
■
Lift screw (11/1) only far enough that the
large washer can be pushed in.
■
Push screw (11/1) through the holes in
the operating arm, large and small wash-
ers and transverse plate.
4. Push small washer (13/7) and self-locking nut
(13/8) from below onto the screw and tighten
securely.
5.1.4 Attach retaining claws with protective
bracket [LSV 550/6] (14 – 16)
Installing protective brackets (14, 16)
1. Push long protective bracket (16/1) onto left-
hand retaining claw (16/2):
■
Insert two M6 x 16 screws (14/1) from
above through protective bracket and re-
taining claw.
■
Push washer (14/2) and self-locking nut
(14/3) from below onto each screw and
tighten securely.
2. Push short protective bracket (16/3) onto
right-hand retaining claw (16/4):
■
Insert two M6 x 16 screws (14/4) from
above through protective bracket and re-
taining claw.
■
Push washer (14/5) and self-locking nut
(14/6) from below onto each screw and
tighten securely.
Installing retaining claws (15, 16)
Perform the steps described here for both retain-
ing claws:
1. Push a washer (15/1) onto each of the star
handles (15/2).
2. As shown in Figure (16):
■
Push left-hand retaining claw (15/3, 16/2)
onto left-hand operating arm (15/4).
■
Push right-hand retaining claw (15/5,
16/4) onto right-hand operating arm
(15/6).
3. Insert two star handles with washers into
each retaining claw and tighten securely.
5.2 Assembly for LSV 560/8 (18 – 28)
5.2.1 Attach the wheels [LSV 560/8] (18)
Perform the steps described here for both
wheels:
1. Push the following parts onto wheel axis
(18/1):
■
Wheel (18/2)
■
2 washers (18/3)
2. Push wheel shaft with wheel and washers in-
to bearing (18/4) as far as it will go.