AL-KO Easy Crush LH 2810, Instructions For Use Manual

Page: 25 / 220

442981_a 25
Maintenance and care
2. Then press the ON switch (06/1).
3. The material to be shredded is pulled in.
Reverse:
See see chapter 6.5 "Clearing a cutting disk/cut-
ting drum blockage", page 25 .
6.4 Switching off the motor (06)
1. Press the OFF switch (06/2) to switch the
motor off.
CAUTION! Damage to the machine due to
improper operation! Incorrect handling can re-
sult in machine damage!
■
Only feed material to be shredded after the
machine has been switched on.
■
Do not feed material to be shredded after the
machine has been switched off.
6.5 Clearing a cutting disk/cutting drum
blockage
Clearing a cutting disk blockage (MH 2810)
(09/10 )
1. Switch off the shredder.
2. Disconnect the machine from the mains pow-
er supply.
3. Loosen locking screw (09/1) and remove
shredder upper section (09/2).
4. Remove blocking material to be shredded.
5. Check cutting disk and shredder blade (10/3)
for damage.
6. Then fit shredder upper section (09/2) and
tighten locking screw (09/1) again.
7. Reconnect the machine to the mains power
supply.
8. Then switch on the shredder again.
CAUTION! Danger of crushing when
opening and closing the shredder upper sec-
tion!
Hand and finger injuries may occur!
■
Watch out for hands and fingers when open-
ing and closing the shredder upper section.
Clearing a cutting drum blockage (LH 2810)
(06/08)
1. Switch off the shredder.
2. Turn direction of rotation switch (06/4) to the
right (06/5) and press the ON switch (06/1)
(reverse).
3. The material to be shredded should now be
released upwards.
4. Switch off the machine and wait for the cut-
ting drum to come to a standstill.
5. Then turn direction of rotation switch (06/4) to
the left (06/6) again.
6. Then switch on the shredder again.
If the material to be shredded is not released up-
wards:
1. Loosen the adjusting screw of the counter-
plate (08/1), until the cutting drum runs freely
again and the blockage is cleared.
2. Readjust the counterplate, see description
"Readjusting the counterplate".
If the blockage cannot be cleared, please contact
our responsible customer service.
WARNING! Risk of injury due to lack of
concentration while working! Ejected parts can
cause very severe injuries!
■
Pay attention to ejected parts and keep your
face away from the hopper.
6.6 Emptying the collector box (11/12)
1. Switch off the shredder.
2. Pull the lock (11/1) down and the collector
box (11/2) out of the base.
3. Place the empty collector box (12/2) onto the
guide rail (12/1) and push it completely into
the base.
4. Push lock (12/3) up until it engages.
6.7 Transporting the shredder
Transport the shredder only with the shredder up-
per section closed and locked.
1. Switch off the motor and wait for the cutting
disk (MH 2810) or cutting drum (LH 2810) to
come to a standstill.
2. Then disconnect the machine from the mains
power supply.
3. Hold the shredder at the handle (01/1) and tilt
the machine slightly.
4. Pull the machine behind you when moving to
the next location. Pay attention to the ground
to prevent the machine from tipping over
during transport.
7 MAINTENANCE AND CARE
Repairs are only allowed to be performed by
qualified specialists, and with the exclusive use of
genuine spare parts.
■
After each use, check the shredder for wear
and renew any damaged components.
■
Keep venting slots (01/5) free from residues
or accumulations.