manualshive.com logo in svg

Akva AKVA 2 BOX, Manual

Share
Download
Akva AKVA 2 BOX Manual Download Page 35

 

                                                                                                                               

    

Page            

32

AKVA MIRA WITHOUT HEADBOARD  

 

•

 

Assemble the base, position stabilisers and base boards. See instructions for Akva Box.    

•

 

Fit the Mira frame by fastening the angle brackets loosely on the upholstered side pieces. 

Loosely fit the upholstered foot and head end pieces to the side pieces. Hardware bag no. 
3 is to be used above the base boards, bag no. 2 below the base boards. Fasten the 
corners of the frame one by one. Begin with the screws farthest in. 

•

 

When the frame is tightened, it is fastened to the base board with angle brackets in the 
middle of each upholstered piece (Hardware bag no. 1.) 

•

 

Fit the rest of the bed. See instructions for HARDSIDE and INSIDE respectively, beginning 
from item (3.) When Inside version: the lower foam is only to be placed on the base 
boards, it is not to be secured with fastening tape.   

 
 

 

 
 
 
 
 

 

Summary of Contents for AKVA 2 BOX





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands