background image

 

Aktobis AG, Borsigstr. 20, D-63110 Rodgau / Germany 

www.AKTOBIS.de

 

Email: [email protected] 

 
 

Important safety instructions: 

 
-  Please note that the radiant heater can become very hot during operation, so keep a 

sufficient distance at all times. Especially away from flammable or easily combustible 
objects! Never touch the heating head during operation! 

-  Do not place/mount the radiant heater directly next to a power socket ! 
-  Never use the radiant heater on moving surfaces, objects or vehicles ! There is a risk that 

the radiant heater may tip over. 

-  It is recommended to use a separate power source (socket) to supply the radiant heater. 

(Please do not use multiple sockets for operating the radiant heater). 
Furthermore, please ensure that the power cable is always laid with sufficient distance to the 
heat source. 

-  Supervise the radiant heater when children are near the appliance ! 
-  Watch out for electricity, never walk into or insert objects into the appliance ! 
-  Do not place any objects on or directly in front of the radiant heater ! 
-  Please ensure sufficient space/clearance around the unit ! 
-  Only qualified personnel or electricians are allowed to open the unit ! 
-  Make sure that no moisture gets into the unit ! 
-  The radiant heater must not be used in the direct vicinity of bathtubs, washbasins or 

swimming pools ! 

-  Only use the recommended voltage for operating the unit ! 
-  Make sure that the power cable is unfolded (untied) before connecting it to the socket ! 
-  Make sure that the plug is cleanly and properly connected to the socket before using the 

appliance ! 

-  Never reach near the plug or socket with wet hands ! 
-  Do not repair defective or damaged cables on the unit yourself, you could get a severe 

electric shock ! 

-  Make sure that highly flammable substances (e.g. gases/oils etc.) are never in the vicinity of 

the unit ! 

-  Ensure that the area on and around the unit remains free of dust, cobwebs and similar dirt at 

all times to prevent accidental ignition (fire) ! 

-  If the connecting cable of this appliance is damaged, it must be replaced by the 

manufacturer or its after-sales service or a similarly qualified person in order to avoid 
hazards. 

-  This appliance is not intended to be used by persons (including children) with reduced 

physical, sensory or mental capabilities, or lack of experience and/or knowledge, unless they 
have been given supervision or instruction concerning use of the appliance by a person 
responsible for their safety. 

-  If you are not going to use the unit for a long time, switch it off and disconnect the mains plug 

 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for WDH-180DS














Reviews: