Activation of the device
Before activating the device, make sure that there is enough reception at the installation location.
Activated devices may not be returned.
1.-Access akonet.cloud or open the mobile application Akonet.app (requires registration).
2.-Register the new device by pressing
and following one of these two methods:
Ÿ
Manually enter the serial no. and the activation code that appear on the device's label.
Ÿ
Press
and capture the QR code of the device's label (requires that the PC or mobile device used for accessing
akonet.cloud has a camera).
3.-Once both steps have been completed, activate the device by pressing the pushbutton for 9 seconds. The 3 indicator lights
flash.
4.-Wait until the process has finished (approximately 3 min). If the green LED lights up, transmission is OK and the device has been
activated correctly. If the red LED lights up, transmission has failed. The device will make 2 more attempts in the course of 1 hour and
will try again once a day. If the problem persists, check coverage in your area or change the location of the device.
Operation
Pushbutton
Long press (> 9 sec.):
Activate the initial start-up of the device. This should only be done after registering in akonet.cloud.
When activated, the 3 indicators flash and during transmission the blue indicator flashes.
Medium press (> 3 sec.):
Forces data transmission to akonet.cloud. When it wakes up, the 3 indicators flash and during
transmission the blue indicator flashes.
Short press (< 3 sec.):
Displays the status of the battery with the green indicator:
Battery OK
ON:
Flashing:
Low battery, replace as soon as possible.
Indicators
Display the status of the device only after a medium press (forced transmission), the rest of the time they remain off.
RED
Flashing:
An error has been detected in the operation, after 3 seconds the indicator turns off.
Constant:
The transmission could not be carried out, review the coverage, after 3 seconds the indicator turns off.
GREEN
At the end of a transmission, it indicates the level of current coverage:
Constant:
Good signal quality
Flashing:
Medium signal quality
Flash:
Poor signal quality
After 3 seconds the indicator turns off.
BLUE
Flashing:
Transmission in progress
Logging and sending data
The device is shipped from the factory in an inactive state, therefore it does not transmit or log any information until it is activated (see “Registering the device”).
Once active, the device logs the temperature, moisture, alarms and external probe temperature (depending on model) data at regular intervals. The time between each log is
defined by the option “L2 - Data logger interval frequency” under the heading “Parameters / dlG - Datalogger” of
The sending of logged data to akonet.cloud takes place when it meets one of the following criteria:
—
The elapsed time defined using the “Tx - Cloud transmission interval”, defined in paragraph “Parameters / nb - Narrowband”, has run out.
—
An alarm has been detected with forced transmission configuration.
—
A transmission has been forced with a medium press.
For more information on the operation of akonet.cloud and on how to configure the device, consult manuals 5000H001 and 5000H011 respectively. These are available on our
website
.
>9"
*Battery life may vary depending on the ambient temperature, the level of coverage and the configuration of the device.
Technical specifications
Power supply
Battery
...........................................................
LiSOCI2, 3.6 Vdc, 6.5 Ah
Estimated life of the battery................................................................. up to 8 years*
Measuring range ............................................................................ -200 to 100 ºC
Resolution .....................................................................................................0.1 ºC
Precision .................................................................................-40 to 40 ºC: 0.5 ºC
±
Rest: ............................................................................................................ 1 ºC
±
Band: ...................................................................NBIoT (Narrow band, B20 and B8)
B20 .................................................................Tx: 832 - 862 MHz; Rx: 791 - 821 Mhz
B8 ...................................................................Tx: 880 - 915 MHz; Rx: 925 - 960 Mhz
Maximum transmission power
conductive
..................................................23.5 dBm
Akonet.app
Mobile application available
for IOS and Android
Antenna
.................................................................Internal
AKO-59840x
.................................................................External
AKO-59841x
Working ambient temperature
to
................................................................-40 50 ºC
Storage ambient temperature
-40 a 60 ºC, recom30 ºC
................................
Range of moisture permitted
without condensation
.............................0 - 100 % RH (
)
Protection degree
AKO-59840x
.................................................................
IP6
7
.................................................................IP65
AKO-59841x
Dimensions ......................................................107 mm (W) x 85 mm (H) x 39 mm (D)
Probe lenght......................................................................................................3 m
Red: Operation
Green: Battery /
Coverage
Pushbutton
Blue: Transmission
