background image

 

29 

Model No: CT-21FD9CP_21FD9M 
Version 1.0 

 

 

7-1-1. V-SIZE ADJUSTMENT. 

- Select the V-SIZE by pressing CH UP/DOWN key 
- Adjust the V-SIZE by pressing VOL UP/DOWN key for approximately one-half inch over 
scan at top and bottom of picture screen. 

 
7-1-2. V-CENTER ADJUSTMENT. 

- Select the V-CENTER by pressing CH UP/DOWN key. 
- Adjust V-CENTER so that the vertical center of the picture may be coincident with the 
mechanical center of CRT. 

 
7-1-3. H-CENTER ADJUSTMENT. 

- Select the H-CENTER by pressing CH UP/DOWN key. 
- Adjust the H-CENTER by pressing VOL UP/DOWN key to be agreed with screen center and 
mechanical center. 

 
7-1-4. V-LIN ADJUSTMENT. 

- Adjust V-LIN by pressing VOL UP/DOWN key. 

 

7-1. V-SIZE / V-CENTER / H-CENTER (F2) 

- Receive the video no signal. 
- Select the SERVICE mode by pressing CH UP/DOWN key. 
- Make the horizontal line by pressing VOL UP/DOWN key. 
- Adjust the SCREEN, till horizontal line is just disappeared. 

 
7-2. SCREEN (SERVICE) ADJUSTMENT (F3) 

- Receive a black and white pattern or white balance adjusting pattern. 
- Before attempting white balance adjustment, the receiver should be operating for at least 
15minites. 
- Check the all of position to the reference value (nominal center) 
- The reference color of the measurement equipment set to G. 
- Adjust the CUTOFF G, CUTOFF R, and CUTOFF B at bias mode. 
- Adjust the R DRV, B DRV at drive mode. 

 
7-3. WHITE BALANCE ADJUSTMENT (F3) 

- Change Mode to VIDEO NO SIGNAL 
- Select the NORMAL1 mode in the fuzzy key. 
- Select the SUB BRIGHT mode by pressing CH UP/DOWN key in FACTORY2 mode. 
- Adjust the SUB BRIGHT value till disappeared to back screen by pressing VOL UP/DOWN. 

 
 

 
 

 

 
 

 
 

 

 
 

 
 

 

 

Summary of Contents for CT-21FD9 Series





















































Reviews: