background image

 

     

 

Model no.: .CT-21CBP5CP.doc 
version 1.0 

8

 
 
 
 

MAINTENANCE 

 
 
 
 

 

 

1. 

Place the TV set on a stable stand or base that is of adequate size and strength to 
prevent it from being accidentally tipped over, pushed off, or pulled off. Do not 
place the set near or over a radiator or heat register, or where it is exposed to direct 
sunlight.  

 

2. 

Do not install the TV set in a place exposed to rain, water, excessive dust, 
mechanical vibrations or impacts.  

 

3. 

Allow enough space (at least 10cm) between the TV and wall or enclosures for 
proper ventilation.  

 

4. 

Slots and openings in the cabinet should never be blocked by clothes or other 
objects.  

 

5. 

Please power off the TV set and disconnect it from the wall immediately if any 
abnormal condition are met, such as bad smell, belching smoke, sparkling, 
abnormal sound, no picture/sound/raster. Hold the plug firmly when disconnecting 
the power cord.  

 

6. 

Unplug the TV set from the wall outlet before cleaning or polishing it. Use a dry soft 
cloth for cleaning the exterior of the TV set or CRT screen. Do not use liquid 
cleaners or aerosol cleaners.  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

Summary of Contents for CT-21CBP5CP























































Reviews: