Akai PDP5090, Owner'S Instructions Manual

Page: 24 / 36

47 46
How to Set up Your Display Setting (Windows only)
Notes:
The plasma panel of this monitor is composed 1366 pixels & 768 lines. That is, the best resolution of
this monitor is 1366 X 768.
Thus, select 1366 X 768 resolution in same way as below when you control the display setting, If your
video card does not support 1366 X 768 resoution, the resolution of 1024 X 768 is recommended. If
you select one of resolutions above, you can use this monitor in best condition.
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card. But even if your actual screens look different, the same, basic set-up information will apply
in almost all cases. (If not, contact your computer manufacturer or AKAI Dealer.
On the windows screen, select in the following
sequence : Start
➝ Settings ➝ Control Panel.
When the control panel screen appears, click on
“Display” and a display dialog-box will appear.
Select the “Settings” tab in the display dialog-box.
The two key variables that apply the PDP-PC inter-
face are “resolution” and “colors.” The correct set-
tings for these two variables are:
• Size (sometimes called “resolution”):
1024 x 768 pixels.
• Color: “24-bit” color (might also be expressed
as “16 million colors”)Shown at left is a typical
screen for “Display” dialog box.
If a vertical-frequency option exists on your dis-
play settings dialog box, the correct value is “60”
or “60 Hz.” Otherwise, just click “OK” and exit
the dialog box.
Continued...
Notes:
Both screen position and size will vary, depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
(N: Negative / P: Positive)
• The PDP might operate abnormally if a non-standard video format is selected.
• When this PDP is used as a PC display, 24-bit color is supported (over 16 million colors).
• Your PC display screen might appear different depending on the manufacturer (and your particular
version of Windows).
Check your PC instruction book for information about connecting your PC to a PDP.
• If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5kHz
(horizontal).
• In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is
turned off (or if the PC is disconnected). If so, press the Source button to enter the VIDEO mode.
Also, make sure that the PC is connected.
• Connect only a PC monitor to the monitor output port while viewing the PC screen.
(Otherwise, random signals might appear).
*
This mode is only supported by a particular video card(PIXEL PERFECT made by IMAGINE
GRAPHICS Ltd.).
Video signal Dot X Line
640 X 350
640 X 400
720 X 400
640 X 480
848 X 480
800 X 600
1024 X 768
1152 X 864
1280 X 768
(W-XGA)
1280 X 1024
1366 X 768*
70.086
85.080
85.080
70.087
85.039
59.940
72.809
75.000
85.008
60.000
72.000
75.000
85.000
56.250
60.317
72.188
75.000
85.061
60.004
70.069
75.029
84.997
75.000
60.000
75.000
60.020
75.025
60.000
31.469
37.861
37.861
31.469
37.927
31.469
37.861
37.500
43.269
29.838
35.156
36.072
37.650
42.925
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.677
67.500
47.700
60.150
63.981
79.976
48.200
N
N
P
P
P
N
N
N
N
P
P
P
P
N/P
P
P
P
P
N
N
P
P
P
P
P
P
P
N
P
P
N
N
N
N
N
N
N
N
N
N
N
N/P
P
P
P
P
N
N
P
P
P
N
N
P
P
N
Vertical
Frequency (Hz)
Horizontal
Frequency (kHz)
Vertical
polarity Horizontal
polarity
IBM PC / AT
Compatible