AJA R Series Installation And Operation Manual Download Page 11

 

1

 

11

 

AJA R20AD 10-bit Universal Decoder User Manual

 

Federal Communications Commission (FCC) Compliance Notices

 

Class A 
Interference 
Statement

 

This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to Part 15, Subpart B of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a commercial installation. This equipment generates, 
uses, and can radiate radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. Operation of this 
equipment in a residential area is likely to cause harmful interference in which case the user will 
be required to correct the interference at his own expense. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more 
of the following measures:

 

• 

 

Reorient or relocate the receiving antenna.

 

• 

 

Increase the separation between the equipment and receiver.

 

• 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver 

is connected.

 

• 

 

Consult the dealer or an experienced radio/TV technician for help.

 

FCC Caution

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation.

 

Canadian ICES Statement

 

Canadian Department of Communications Radio Interference Regulations

This digital apparatus does not exceed the Class A limits for radio-noise emissions from a digital 
apparatus as set out in the Radio Interference Regulations of the Canadian Department of 
Communications. This Class A digital apparatus complies with Canadian ICES-003.

Règlement sur le brouillage radioélectrique du ministère des Communications

Cet appareil numérique respecte les limites de bruits radioélectriques visant les appareils 
numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du 
ministère des Communications du Canada. Cet appareil numérique de la Classe A est conforme 
à la norme NMB-003 du Canada.

 

European Union and European Free Trade Association (EFTA) 

 

Regulatory Compliance

 

This equipment may be operated in the countries that comprise the member countries of the 
European Union and the European Free Trade Association. These countries, listed in the 
following paragraph, are referred to as The European Community throughout this document:

AUSTRIA, BELGIUM, BULGARIA, CYPRUS, CZECH REPUBLIC, DENMARK, ESTONIA, FINLAND, 
FRANCE, GERMANY, GREECE, HUNGARY, IRELAND, ITALY, LATVIA, LITHUANIA, LUXEMBOURG, 
MALTA, NETHERLANDS, POLAND, PORTUGAL, ROMANIA, SLOVAKIA, SLOVENIA, SPAIN, SWEDEN, 
UNITED KINGDOM, ICELAND, LICHTENSTEIN, NORWAY, SWITZERLAND

 

Appendix A: Safety & Compliance

Summary of Contents for R Series



















Reviews: