2
|
01252 359760 • ajproducts.co.uk
Thank you for using this lift table. Your lift table is made of
high quality steel and is designed for the horizontal lifting and
transport of loads on a level, fixed base. For your safety and
correct operation, please carefully read this instruction before
using it and keep it on file for future reference.
Note!
All of the information reported herein is based on data
available at the moment of printing. We reserves the right to
modify our own products at any moment without notice and
incurring in any sanction. So, it is suggested to always verify
possible updates.
1. WARNINGS
1.1
DO NOT put foot or hand in scissors mechanism.
1.2
DO NOT allow other person to stand in front or behind lift table when it is
moving.
1.3
DO NOT move lift table when table is in raised position. Load could fall
down.
1.4
DO NOT enter under table.
1.5
DO NOT overload lift table.
1.6
DO NOT put foot in front of rolling wheels, Injury could fall down.
1.7
WATCH difference of floor level when moving lift table. Load could fall
down.
1.8
DO NOT use lift table on slope or inclined surface, lift table may become
uncontrollable and create danger.
1.9
DO NOT lift people. People could fall down and suffer severe injury.
2. CAUTION
2.1
Read this operation manual carefully and understand completely
operating lift table. Improper operation could create danger.
2.2
This lift table is a movable lifter designed to lift or lower rated load on
table. DO NOT use lift table for other purpose than its intended use.
2.3
DO NOT allow person to operate lift table that dose not understand its
operation.
2.4
DO NOT lower table too fast. Load could fall down and create danger.
2.5
KEEP watching the condition of load. Stop operating lift table if load
becomes unstable.
2.6
Braking lift table when sliding load on or off table.
2.7
DO NOT side or end load. Load must be distributed on at least 80% of
table area.
2.8
DO NOT use lift table with unstable, unbalanced loosely load.
2.9
Practice maintenance work according to service instructions.
2.10
DO NOT modify lift table without manufacturers written consent.
2.11
REMOVE load from table and use safety stopper to prevent table from
lowering when servicing lift table.
2.12
This lift table is not designed to be water resistant. Use lift table under dry
condition.
3. DAILY INSPECTION
Daily inspection is effective to find the malfunction or fault on lift table. Check lift
table on the following points before operation .
(1) Check for scratch, bending or cracking on the lift table.
(2) Check if there is any oil leakage from the cylinder.
(3) Check the vertical creep of the table.
(4) Check the smooth movement of the wheels.
(5) Check the function of brake.
(6) Check if all the bolts and nuts are tightened firmly.
CAUTION: DO NOT use lift table if any malfunction or fault is found.
4. OPERATING LIFT TABLE
4.1 How to use the brake.
CAUTION
Brake lift when not moving it in order to prevent sudden movement.
The brake is equipped with the swivel caster on the right side.
(1) Brake the wheel, press the brake pedal.
(2) Release the brake, lift up the brake pedal.
4.2 Lifting the table
WARNING
1. DO NOT overload lift table. Stay within its rated capacity.
2. DO NOT side or end. Load must be distributed on at least 80% of table area.
Press the lifting pedal several times until the table reaches the desired position.
The table does not elevate after reaching the highest position even if the lifting
pedal is pressed. The table lowers slightly after reaching the highest position.
MAXIMUM CAPACITY OF TABLE
TFD80 - 800 kg
NOTE:
The hydraulic cylinder is designed to hold table. As is the nature of hydraulic
system, table lowers very slowly over and extended period of time. Please note
the table does not stay at the same position indefinitely.
4.3 Lowering table
WARNING
DO NOT put foot or hand in scissors mechanism
• Knob rotating makes table down..
Pull the control handle make table down.
5. SPECIFICATIONS
Model
Capacity
(kg)
Table
(Mm)
Table
Height (mm)
Wheel
(Mm)
Weight
(Kg)
TFD80
800
1220x610
445-1500
Ø 127
195
6. SERvICE INSTRUCTIONS
6.1 Lubricate each point described below every month:
6.2 Change hydraulic oil every 12 months.
Lubricating Points
(1) Fitting of cylinder---Oil
(2) Roller friction surface---Grease
(3) Link pin ---Oil
(4) Pedal fitting point---Oil
(5) Grease nipple---Grease
