background image

ICE EX04-18 Heat I&O Manual 06/2020 Rev.1

 

6

2.3  Mechanical Installation of the Heat Exchanger

Do not press on the heat exchanger cooling fins during installation - this will damage 

them. If the heat exchanger fins are damaged, repair them before moving it. The 

mounting flange is factory installed. Ensure the waterproofing seal is in place before 

installing the unit.

2.4  Electrical Installation

The electrical installation of the air conditioner includes: 

• 

Connecting the power cables 

• 

Connecting the communication & alarm output cables 

IMPORTANT

All the electrical connections should comply with the standards of the national 

and local electrical codes. Please disconnect all the power supplies for the air 

conditioner before the installation. 

 

WARNING FIRE HAZARD

Improper adjustment, alteration, service, maintenance or installation could cause 

serious injury, death and/or property damage.
Installation or repairs made by unqualified persons could result in hazards to 

you and others. Installation MUST conform with local codes or, in the absence of 

local codes, with codes of all governmental authorities have jurisdiction.
The information contained in this manual is intended for use by a qualified 

service agency that is experienced in such work, is familiar with all precautions 

and safety procedures required in such work, and is equipped with the proper 

tools and test instruments.

The power connection should match the marking on the wiring, It is recommended that 

the input circuit breaker be at least 16A.Some models’ temperature sensor is externally 

located. Check to be sure the wiring input is correct and securely connected.

2.5  Power Input Cables

IMPORTANT

Please refer to the specific wiring definition mark on the unit. 

 

AC Power Input:

If the unit needs AC input, will be an external AC input L, N, PE terminals access to the 

corresponding position, as shown in Figure 2.1, please be sure to connect power supply 

in accordance with instructions. 

Figure 2. AC Power Input Wiring Diagram

Summary of Contents for EX04CDHC1A














Reviews: