background image

3

Preparation before use

The air conditioner has an  Auto-Restart function.  

    

Each time after the remote control is replaced with new batteries or is energized, 

 auto presetting

heat  pump.If the air conditioner you purchased is a Cooling Only one, heat pump remote controller can also be used.

 remote control

Remote Control presetting

Before using the air conditioner, be sure to check and preset the following.

Auto Restart Presetting

 Hold down any button on remote control to activate the back light. It automatically shuts off 10 seconds later.

Note: Back-light is an optional function.

Back-light function 

(optional)

 

of  Remote Control

This appliance is made of recyclable or re-usable material. Scrapping must be carried out  in
compliance with local waste disposal regulations. Before scrapping it, make sure to cut off the
mains cord so that the appliance cannot be re-used. 
For more detailed information on handling and recycling this product, contact your local authorities
who deal with the separate collection of rubbish or the shop where you bought the appliance. 

SCRAPPING OF APPLIANCE 

This appliance is marked according to the European Directive 2012/19/EC, 
Waste Electrical and Electronic Equipment (WEEE). 

 

This marking indicates that this product should not be disposed
with other household wastes throughout the EU. To prevent possible
harm to the environment or human health from uncontrolled waste 
disposal,recycle it responsibly to promote the sustainable reuse of 
material resources. To return your used device, please use the return 
and collection systems or contact the retailer where the product was 
purchased. They can take this product for environmental safe recycling.

Note

Preset

Safeguarding the environment

 When charging refrigerant into the system, make sure to charge in liquid state,if the
 refrigerant of the appliance is R32.Otherwise, chemical  composition of refrigerant
 (R32) inside the system may change and thus affect performance of the air conditioner. 

   According to the character of 
   of the tube is very high, so be sure to be careful when you install and repair the 
   appliance.  

refrigerant (R32,the value of GWP is 675), the pressure 

If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
Installation of this product must be done by experienced service technicians 
professional installers only in accordance with this manual.

 

The temperature of refrigerant circuit will be high, please keep the 
interconnection cable away from the copper tube.

For the multi system, the refrigerant refer to the multi outdoor unit.

Summary of Contents for High Wall HDA


















































Reviews: