It is necessary to pair the transmitter and receiver to prevent interference from radio controllers operated by other users. This operation is referred to as
'binding'. Once the binding process is complete, the setting is remembered even when the transmitter and receiver are turned OFF, therefore, this procedure
usually only needs to be done once. Under some circumstances, the receiver may not operate after turning the transmitter and receiver ON. If this occurs,
perform the binding process again.
1) Turn on the transmitter, then press the two Function keys at the same time until Function Menu F3 is
displayed. If the SET-UP menu is not automatically highlighted, continue to press the Function key until
the SET-UP menu is highlighted.
2) With the SET-UP menu highlighted, press the Function key to select [BIND] in the Programming
Window. SET BIND BUTTON will be displayed in the Programming Window.
Before beginning the binding process, plug your receiver battery into the switch, then plug the switch into the BATT/DSC slot in the receiver, making
sure that the polarity is correct. Make sure that both the transmitter and receiver are turned OFF.
When the binding procedure is successful, the Bind LED on the receiver will stay solid blue when both the transmitter and receiver are turned ON. If
the Bind LED on the receiver is blinking rapidly, the transmitter and receiver are not paired. In this case, turn both the transmitter and receiver OFF,
then repeat the binding procedure.
© 2009, All Rights Reserved. Version 1
http://www.airtronics.net
Global Hobby Distributors
18480 Bandilier Circle
Fountain Valley, CA 92708
Telephone: (714) 963-0329
Fax: (714) 964-6236
Email: [email protected]
Airtronics is Distributed Exclusively in North America by:
warranty
Your Airtronics 92451 Super Response 2.4GHz FHSS-3 receiver is warranted against manufacturer defects in materials and workmanship, at the original
date of purchase.
Any modifications or abuse of the product will void any warranty. Crash damage will not be covered by any warranty. The receiver is not waterproof.
Water damage will not be covered by any warranty. Damage caused by the use of analog servos will not be covered by any warranty.
bindinG tHe receiver to your transmitter
This section describes binding the 92451 Super Response 2.4GHz FHSS-3 receiver to the Airtronics M11X FHSS-3 transmitter. For information on
binding the receiver to a different FHSS-3 transmitter, such as the Airtronics MX-3X, see your transmitter's Operating Manual.
usinG tHe receiver - nor and sHr response modes
The 92451 Super Response 2.4GHz FHSS-3 receiver can operate in two different modes, based on the Servo Mode Setting in the transmitter's Modulation
Menu. To change the Servo Mode Setting, refer to your transmitter's Operating Manual.
Use the following two modes as described below:
NOR (Normal <> Servo High Response)
- When the transmitter Servo Mode Setting is set to NOR Mode, any brand of digital servo can be used. In NOR
Mode, digital servo speed is increased, even beyond the manufacturer's stated speed. This results in ultra-fast servo transit times.
SHR (Servo High Response <> Servo Super Response)
- When the transmitter Servo Mode Setting is set to SHR Mode, and only when used in conjunction
with Airtronics Super Response servos, servo reaction time is increased. This results in virtually no lag between the time you move the transmitter controls and
when the servos react. This makes you feel more 'connected' to your model than ever.
To take advantage of SHR Super Servo Response, Airtronics Super Response servos must be used. You will not notice any difference if using another
type of servo. If you use another type of servo, use NOR Mode. For more information on Super Response servos, see your local Airtronics dealer.
5) After ~2 seconds release the Bind Button. The Bind LED on the receiver will continue to blink slowly.
Quickly press the ENTER key on the transmitter. SENDING will be displayed in the Programming
Window, the Bind LED on the receiver will blink rapidly, then the Bind LED on the receiver will turn
solid indicating the binding process is complete.
After releasing the Bind Button, you must press the ENTER key quickly (within a couple of
seconds). If you take too much time, you will need to restart the binding process.
3) Press the key. SEND BIND COMMAND will be displayed in the Programming Window.
4) While holding down the Bind Button on the receiver, turn the receiver ON. The Bind LED on the
receiver will blink slowly.
Use the tip of a pencil or a 1.5mm hex wrench to reach the Bind Button on the receiver.
