background image

G

ELECTRICAL SYSTEM

G - 8

Maintenance

Lubrication

To lubricate the elevating gear apply a liberal amount of silicone spray lubricant to the 

elevating gear with the lift in the down position, then run the lift up and down a few 

times to distribute lubricant over gears. 

Lubricating Rotating Gear Housing

In the event that rotating the antenna becomes difficult, lubricating the bearing surface 

between the rotating gear housing and the base plate can restore normal operation. 

Any spray type silicone lubricant may be used. 

Elevate antenna and remove setscrew from rotating gear housing as shown. Spray lu-

bricant into hole and around edges of gear housing. Rotate gear housing until lubricant 

coats bearing surfaces and antenna rotates freely. 

TV Booster/12 Volt Outlet

The TV booster amplifies the signal from the TV antenna. Pushing the small button 

activates and deactivates the booster. A green light comes on when the booster 

is activated.

 

For viewing while hooked up to an exterior cable TV source,  turn the 

booster off.

NOTE

: The TV Booster must be on to receive antenna signals and off for cable TV 

operation. 

Please review the antenna and booster manuals include in your owner’s packet 

before operating the system.

Wireless Speakers 

(Optional)

Your  trailer  may  have  wireless  speakers  which  is  included  in  the  optional  upgrade 

package. An operating guide is included with each kit. 

LUBRICATE HERE

SPRAY AROUND EDGES REMOVE SET SCREW

TV Outlet 
w/Booster & 
12 Outlet

12 V
Outlet

Booster
Switch

TV Cable
Hook Up

Light

Summary of Contents for 2008 Safari








































































































Reviews: